C201-C Jenn-Air Cooktop - Instructions

Easily removed the old knobs and applied the new ones.

I unplugged the stove. Took out the burner and removed receptacle by pulling it out of the bracket and clipping the wires. One thing you want to make sure is that when you clip the wires from the receptacle you're replacing you leave enough wire so that you can connect them to the wires on the new receptacle when it is in place on the stove. I had just enough but would have liked more. The bracket I received didn't match the one on the stove so I used the one on the stove since the receptacle itself was the same as the one I was replacing.

Turn off elec. power at breaker box. Check twice. Removed burner switch cover. caarefull remove wires from switch, note with color to which terminal remove nut on switch replace new switch replace wires to switch, replace cover turn on power. ready.

Kill power to range unit at the breaker. Remove 2 screws on back of center control panel. Lift control panel up and toward rear of unit. Unscrew retainer nut which holds switch in the control panel. Carefully note wiring connections, and unplug all 5 wires from switch with pliers. Remove old switch. Reconnect all wires to new switch. Reattach switch to panel with retainer nut. Replace control panel in range with screws. Turn on power.

Took everything apart and replace the new parts but what I really want to share is the prompt shipment of my parts, I'm very satisfied and I will recommend the web site (THANK YOU)

I first replaced the element and the receiver. This required splicing lines which was very easy. It still did not heat (even though my element indicator light was on) so I replaced the switch regulator. This took a little time because of the small space on my model. In fact, I had to replace a wire that had shorted by splicing a 3 inch section into it. When that was done, I simply re-connected the 5 wires in the original positions and reattached the cover. It works like a charm and my wife is delighted because we are hosting a family reunion/baby shower tomorrow!

After buying a 'universal' part at Lowe's and it not fitting correctly and shorting out the burner, I went online and found this source for an exact replacement part. Beside having to disassemble the drop in stove burner two or three times it went well when I had the correct part. I lost one screw somewhere and that delayed me a short time to find a replacement. Thus the 1 to 2 hours. It would have been about a 30 minute job if I had been smarter.

Turn off the power. Remove 2 screws (in the blower compartment) and lift up the control panel. Release the switch by removing the fastnut. Unplug each wire from the old switch and place it in the cooresponding lug on the new switch. Screw everything back together and cook.

Cut broken wire and existed wire off and put splice on both new and old wires to connect them.
It's easy job.

Removed 2 screws and i nut. Unplug the old switch and plug in the new switch and presto, back in business. Extremely easy. Part was exactly as pictured. Part arrived within 2 days. Great Co. to buy parts from. Highly recommend Partsselect.

I removed the burner elements for three burners by lifting the surface top and unplugging them. I snapped out the plug sockets that were burned out and cut the two wires, one element at a time. Using the included wire nuts I stripped the ends of the cut wire and connected each wire to one of the wires on the new socket. Once the wires were connected I snapped the sockets in place and reinstalled the elements, lowered the surface top and the range was ready to use.

Replaced the switch and put the new surface element in and it works great.

removed the wooden cutter block rt side top and the air exst.vent guard lf side then with a phileps driver 2 screws holding the control knob assm.in. both control knob assm.rt&lf come off the same way. just scraped out what that was left of the old lens stuck in new one and reatached light bulb holder. this bulb holder presses on and slides side ways to lock in place. then snaped control knob assm. back in and tighten the 2 screws. replaced vent guard & wooden cutter block. all was done.

Removed screws by drilling one and using a pliers to remove 2nd one. At first did not have enough wire to pull recepticles out until I relized wires were clipped to back of range to hold in place. Unclipped wires, pulled recepticles out, cut wires and attached new recepticles by connecting wires with wire nuts (I think wire nuts were to small so I used my own a size larger). Another problem that I found was that the recepticles on my range were held in place only by the screws that attached the recepticles to the drip pan flang. I had to bend an L bracket to prop under each recepticle to hold the back of it up so the burner element would sit level over the drip pan.

Pulled out electric heating element and replaced with new. I have had this frustrating problem for 2 years and after replacing the elements they now work like new! My only question, why did it take me so long to replace???