C201-C Jenn-Air Cooktop - Instructions

I first removed power from the stove at the breaker panel. Next, I used the assembly diagrams provided by the parts select website to determine how to open up the stove panel. I opened the oven door to access the four screws holding the front panel holding the knobs. I removed the screws and was able to tilt up the front panel to allow access to the four burner switches. It was easy to swap out the wires on the old defective switch to the new replacement switches. I replaced both defective switches in 15 minutes and tiled the front panel back down into its normal position and put the four screws back into the panel to secure it. Then I turned on the breaker and did a check to see that the parts I replaced were working properly. They were and the total repair time was around 30 minutes without rushing at all.

removed two screws thenpulled element up unpluged wires

Had to drill out screw for old connector bracket and also had to extend wires from controls this took most time. Once done with this used wire cutters to strip back insulation and then put the whole mess back together also used a larger wire nut to reconnect wires.

First I removed a screw that held the element in place then disconnected the two wires . Then I just reattached the two wires put the screw back in place and was done in about 10 minutes. Fairly easy fix, I had this go out a few years ago and had a repairman fix it, and saw how easy it was, so this time I did it myself. Easy job!!

After I removed the piece of metal separating the two wires, I inserted the unit with no problem.

Our stove is from 1978 and was missing all but one drip bowl. I bought all the replacement parts from all the store, (Walmart, Target, Fred Meyer) nothing fit. I finally found this site and they fit perfectly! Thank you. If I have to keep the stove a while longer at least it looks clean and new now, and it still works great!

Simply removed the old heating element and plug the new element terminals into socket.

Turned off power at breaker. Removed screws holding control knobs in position. Removed knob and unscrewed nut holding switch in place. Noted wire positions and undid connections. Connected wires to new unit. Replaced nut and screws and control knob. Restored power and checked operation. You can do this. Don't call an electrician.

The burned control switch was not functioning. It took a while to find the range model number and then the part number of the switch. It was cool that I could see a picture of the part with the part number on the internet so that I was sure to buy the right part.
Once the part arrived, I turned off the power to the range (circuit breaker, 220 V) removed two screws, used nut driver to disconnect switch handle, marked the 5 wires going to the switch, used the needle nose plier to remove the wires, the attached wired to the new switch, placed switch back into position, used nut driver to attach switch to the control unit. Rescrewed control unit in place with two screws.
turned on circuit breaker and tested. All good.
It is clear that this old Jenn Air range and be completely redone to good as new. All parts are available

removed burner and recepticle and replaced new one. You don't have any place to comment on service, so I'll put it here. I talked to Herb and ordered parts with him on a Monday afternoon. He was very helpful. The part came Thursday about noon and I immediatly installed parts and my wife cooked supper (thats southern for the evening meal) that night. A really wonderful experience. Thank's Herb.

1. Shut the breaker off; Jenn-Air's design will have you working around hot leads if you don't.
2. Raise the control panel
3. Remove burner and unscrew the burner connector; trace the wires back to the control panel bottom and remove them
4. On the replacement connector, add the electrical for the control panel. These are not included and can be found at any hardware store; they are a standard size.
5. Connect the new wires and put everything back together.
6. Reset the break and test.

Unplugged old burner element, plugged in new element.

SHUT OFF BREAKER! Remove exhaust grill and switch knob. Remove cooktop switch panel by removing two screws and sliding panel toward exhaust grill. Remove switch retainer nut with deep socket. Transfer wires one by one to new switch. Install new switch tightening retainer nut. Reinstall switch panel with two screws, push knob onto shaft. Turn on breaker.

our cook top is so old, but no need to replace just yet. so I ordered new knobs to get a new look
thank you!

The 15-year-old Jen-Air stove started smelling really bad. I thought it was a dead animal stuck in the exhaust tube which runs under the floor to the outside. I flushed it out with clorine bleach, but it was still bad. It turned out to the be the grease filter. I washed it every week in the diswasher, but it just was not enough to get it clean enough. Finally, the grease went rancid and smelled really bad. This "repair" took about 30 seconds.