C201-C Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ELOISE from MILFORD, OH
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced filter
pulled old one out , cleaned the area & replaced with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- deborah from fort pierce, FL
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old grease filter that I actually did not know I had to change
Removed the old grease screen and cleaned the entire area thoroughly and replaced the screen
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Carthage, NC
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Stove top element not working due to bad receptacle.
Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit.
My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com.
My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marion from aspen, CO
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My Jenn-Air is an "antique." The filter was disgusting!
I had put up with a filter that got more and more raggedy every year, but I thought my 30 yr. old range/grill top was too old for me to find an replacement filter. What a great service you offer. I found you by web-surfing, typed in the model #, and presto--you sent me the shiny new filter. All I had to do was pop it in and throw away the nasty grill (after washing the scent off to keep the bears out of my Colorado garbage.) Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roe from Raleigh, NC
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Falling apart 20 year old grease filter for downdraft counter rangetop
Cleaned out the downdraft cove, inserted the new filter, and put old filter in garbage can. Laughing. Thanks. Wish you had a FAQ's hotline. I'd like to know if the radiant inserts fit the older coil-type models.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Charlotte, NC
- Parts Used:
- WPY04100166, WPY04100165, WP707929, 12200035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cooktop was looking old and worn though there was no working problem.
All of the "old" pieces were very easily removed and replaced with the new pieces. The update looks terrific and works just fine!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from North Andover, MA
- Parts Used:
- 700855K
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burner had no temperature control other that full on.
Locate and open appropriate breaker to kill power to the range. (very important if you intend to see tomorrow).
Pull off the control knob.
Remove 2 screws that hold in control pannel.
Lift out the control pannel to the extent that the wires will let you. (2-3 inches)
Remove the nut that holds the switch/controller in the pannel.
Remove the wires one at a time and reconnect them to the new switch. Make sure to connect them the same way on the new switch.
Re-install the switch in the pannel.
Re-install the pannel in the stove.
Close breaker and test burner contol.
Pull off the control knob.
Remove 2 screws that hold in control pannel.
Lift out the control pannel to the extent that the wires will let you. (2-3 inches)
Remove the nut that holds the switch/controller in the pannel.
Remove the wires one at a time and reconnect them to the new switch. Make sure to connect them the same way on the new switch.
Re-install the switch in the pannel.
Re-install the pannel in the stove.
Close breaker and test burner contol.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- george from burke, AL
- Parts Used:
- WPY707454, WPY707453, WPY04100166, WPY04100165, 715878, 715877
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Wanted to update surface parts to a very old (27 yrs?) Jenn-air range on an island
The first task was to find the rings, drip bowls and elements on the "PartSelect" webpage. It was surprising easy, especially since I have no experience whatsoever in replacing range parts. The ordering was straight-forward, and most of the parts arrived within a week, a couple were back-ordered, but arrived a week later. Instillation was easy - just unplug elements, lift parts out, and insert new parts. I made a mistake in ordering - for the left side of the range, no adaptor rings are needed. I returned these excess parts to PartSelect, and within a week, they refunded the costs of these parts. Overall, I'm very please with the parts and service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Malcolm from White House, TN
- Parts Used:
- W11120795
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Burner Switch Broke were Knob attached
First I cut off power supply, removed screws that held panel on, pulled the switch up and disconnected wires. Installed new switch, being sure to connect wires in the correct places. Refastened panel to stove top. Turned power back on and tested switch and it Worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lucille from Mattoon, IL
- Parts Used:
- WPY700854, WPY04100166, WPY04100165, 715878, 715877, 12001676
- Difficulty Level:
- Difficult
- Total Repair Time:
- 15 - 30 mins
Wanted to "renew" cook top
The drip pans, burner knobs and electric surface elements are easily removed and replaced. The new receptacles for the burners were NOT easy to replace, but electricians were on hand to install when they replaced the cook top into the new counter top. Even the electricians had to read the instructions - and remove the control panel to replace one of the receptables. Looks like a new cook top.
Was this instruction helpful to you?
Thank you for voting!
blower motor died
Pulled the motor and blower wheel from below. Replaced both. I think it was easier to replace the two together than just the motor.I also had old light indicators so we replaced them since the stove was sort of apart. The repair was not difficult at all, and my 30+ stove top looks and runs great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Poway, CA
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lettering on old stove knobs was no longer visible and knobs were loose.
Took the old knobs off and replaced them with the new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Chino, AL
- Parts Used:
- WP5701M122-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Just ugly this time`
It's wonderful to get accessories for this 20 year old Jenn-Air. I love it and now it looks like new.
Was this instruction helpful to you?
Thank you for voting!
Infinite switch ran more than one burner
Purchased 1 infinite switch and installed it on the left front burner. problem still there so I used the switch that I replaced on the rear burner and all was ok. The front switch had been sending full heat to the rear burner,but the problem ended up with the rear switch. The switches are interconnected and all are the same part number.Diagrams on partsselect were the key to a successful repair.To access the switch you need only to remove the fan cover, remove the 2 screws holding the switch assembly and move it foreward and then lift to reveal slide on connectors. Power to the unit is off at the main panel during the entire process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lansing from Alamo, CA
- Parts Used:
- W11120795
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Two heating elements couldn't be controlled - full on
Turned off power.
Removed two screws to free up section of cooktop containing 4 switches - 2 good, 2 damaged. Removed the dials from top of the 2 damaged switches. With an adjustable wrench, loosed nut on stem of switch that fastened switch to assembly. Noted which of the 5 wires on each switch went on which tab. Pulled off 5 wires on one switch, finished removing the nut and removed broken switch. Put in new switch, attached the nut, and replaced 5 wires in exactly the same position, Tightened nut. Replaced dial. Repeated procedure for second switch. Placed section containing the 4 switches back on cooktop and inserted/tighted 2 screws holding it in place.
Turned on power.
Told cleaning people to NEVER put aluminum foil under the burner units again. The foil shorted across the power and damaged the switches.
Removed two screws to free up section of cooktop containing 4 switches - 2 good, 2 damaged. Removed the dials from top of the 2 damaged switches. With an adjustable wrench, loosed nut on stem of switch that fastened switch to assembly. Noted which of the 5 wires on each switch went on which tab. Pulled off 5 wires on one switch, finished removing the nut and removed broken switch. Put in new switch, attached the nut, and replaced 5 wires in exactly the same position, Tightened nut. Replaced dial. Repeated procedure for second switch. Placed section containing the 4 switches back on cooktop and inserted/tighted 2 screws holding it in place.
Turned on power.
Told cleaning people to NEVER put aluminum foil under the burner units again. The foil shorted across the power and damaged the switches.
Was this instruction helpful to you?
Thank you for voting!