CVE407B Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Valentine from Bow, NH
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
control switch was no good
I remove fore screwsfrom the front panel. Then remove two screws to remove the switch and removed the wire plugs then put everything back together again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Maplefalls, WA
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter replacement.
Remove and replace grease filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from castle rock, CO
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
electric element would not function
2 screws to remove
disconnect 220 v power
use long nose pliers to transfer 5 female spade terminals
use nut driver to r@r shaft nut
replace panel with 2 screws
Turn on power and test!---OK!
disconnect 220 v power
use long nose pliers to transfer 5 female spade terminals
use nut driver to r@r shaft nut
replace panel with 2 screws
Turn on power and test!---OK!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Mountain Iron, MN
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old grease filter had hole wore through
Pulled the old one out & inserted the new one. Less than five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Centreville, VA
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Infinite Rotary Control Failed
Replaced one of the four burner control switches on my Jennair cooktop. One of the tricks I use to prevent mistakes is putting the new switch along side the existing one and swap one connector at a time over to the new switch preventing any confusion and negating any need to mark the wires. This differs from your video assistant who disconnected all the wires at once.
gc.
gc.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Redona from Roseville, CA
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Worn out stove top
We replaced the burner grates, knobs, air filter and burner pan. Looks as good as new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Santa Clarita, CA
- Parts Used:
- 12001129
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Fan switch was broken internally.
After reading the other do-it yourselfers I knew it wasn't going to be an easy task. However, when I received my new switch I saw that the hook up and installation would be a snap. My only problem was removal of the old lock washers so I cut them off with my tin snips and once the new switch was attached to the plate I used a socket on the end of a three inch extension. I placed the socket over the new washer and gently tapped on the end of the extention until the washer was seated. It took about two or three taps on each washer and I was finished. Everything went pretty well. Total time to install was about ten minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Traverse City, MI
- Parts Used:
- 12001129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The fan switch broke
remove gas valve knobs, removed two screws holding trim plate on lifted plate removed wires replaced switch and reversed the prior moves.
Very easy
Very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES from McALESTER, OK
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
vent fan cloging up
old filter fell into from removing and cleaning,
removed cover pulled out filter ,replaced it with new one.
removed cover pulled out filter ,replaced it with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- S.. J. from Punta Gorda, FL
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Electric barbecue element not heating
1. Diagnosed problem = switch at fault not element
Made a diagram of wire positions on faulty switch
2. Ordered part = remarkable service! Switch arrived in less than 24 hours
3.Installed new switch
4. Tested appliance = success!
5. Saved $150 and a lot of aggravation
Terrific site. Excellent help in figuring out and solving the problem. Two thumbs up!
Made a diagram of wire positions on faulty switch
2. Ordered part = remarkable service! Switch arrived in less than 24 hours
3.Installed new switch
4. Tested appliance = success!
5. Saved $150 and a lot of aggravation
Terrific site. Excellent help in figuring out and solving the problem. Two thumbs up!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Birmingham, AL
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
bad surface burner switch
1. Turn off power at breaker. Take no chances. Turn on each working burner, fan, oven light to be sure there is no power to the appliance. Then, turn them off.
2. Pull knob on switch straight out to remove.
3. Remove 4 Phillips head screws under control panel. Pull panel gently down, then out toward you slightly to release top edge. Rest control panel on self-clean lock knob.
4. Confirm terminals on new switch match up with old switch.
5. Use needle-nose pliers to gently remove wires from old switch one at a time and place them on the
corresponding terminal on new the switch.
6. Reverse steps 3, 2 and 1. Test switch and burner.
2. Pull knob on switch straight out to remove.
3. Remove 4 Phillips head screws under control panel. Pull panel gently down, then out toward you slightly to release top edge. Rest control panel on self-clean lock knob.
4. Confirm terminals on new switch match up with old switch.
5. Use needle-nose pliers to gently remove wires from old switch one at a time and place them on the
corresponding terminal on new the switch.
6. Reverse steps 3, 2 and 1. Test switch and burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from CARROLLTON, TX
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
could not adj. temp. stayed high all the time
replaced stove top switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Bowie, MD
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
One burner only heated to a high temperature.
I removed 2 screws to release the plate that held four the switces. I removed 2 screws to release the bad switch. I removed one wire at a time and connected the to the same post on the new switch, screwed the switch into place and reinsalled the mounting plate. The stove works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from harlingen, TX
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
no heat to burner
Removed top and front panel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Vienna, WV
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No controlling Left side back burner
Really easy ...followed advice posted from others with same problem. Before anything disconnect the power at the breakers and use a voltage detector to verify there is NO POWER!!!! Only need to remove the two phillips screws on the four controller panel, Slide panel away from you to access the controllers. Match wire/connector for connector from the old to new controller. Reassemble, restore power .. Happy wife!!!. She has been on my case to fix this thing for several years.
Was this instruction helpful to you?
Thank you for voting!