CU240 Jenn-Air Cooktop - Instructions

The hardest part was breaking the caulk seal between the range and the cabinet. An extra set of hands made the job easier, by holding the panel while I connected the switch. The switch was delivered promptly and I am very happy with Parts Select. I found the other repair stories very helpful.

Important: 1) ALWAYS REMOVE ALL POWER FROM THE STOVE. 2) Do not "preassemble" the ceramic recepticle and wire kit. The wires are nearly impossible to remove from the receptacle once inserted. The wire colors have changed and are not the same color as your old wiring. 3) All the fasteners are sheet metal screws, different sizes (note where they are used) and are easly stripped if tighted too hard. Either unplug the stove or open the main circuit breaker to the stove. Take out the right-hand burner cartridge and place it aside. remove the center screw and metal strip from the old receptacle (you will reuse this item). Loosen the control panel from the front of the stove by opening the oven door and remove the four screws holding the control panel in place (Screws are located on the underside of the control panel). The panel slides down about 1/4 inch and tilts forward exposing all the control wiring. Ues a hex-headed driver or large screw driver and remove the drain plug from the drain pan. Use care as there is a small gasket under the drain plug. Remove the four screws holding the burner's pan to the stainless steel stove top. Move the wire bundles aside and GENTLY pull the burner pan half-way out of the stove (it is a tight fit but do not use force. Remove the screws and strap holding the old receptacle from the pan. Withdraw the pan from the stove. (good time to clean the pan and drain plug) With the old receptacle now exposed, assemple the new receptacle and wire harness wire for wire carfully replacing each lead. The new wire harness is inserted into the new receptacle thru the top of the receptacle and will lock in place within the new receptacle. The blades on the end of the wires must point toward the slots in the receptacle. The receptacle wires will be pointing down. Trace each wire and be certain the correct wire is switched out with the proper lug on the control knobs within the stove (needle nose plyers will help but do not force the connections). Gently push the pan halfway back into the stove and attach the new receptacle to the pan with the small metal strap across the back of the receptacle with screws. Push the pan all the way back into the stove and re-attach the pan to the underside of the stove top with sheet metal screws. Re-install the drain plug and drain tube. Tilt the control panel, slide the panel back up into the front of the stove and reattach the control panel with sheet metal screws. Re-install the small metal clip into the front of the receptacle (one end of the clip slides under the stove's stainless top frame). Reenergize. Reset the clock. You're done.

Opened oven door, took four screws out of the front control panel, removed the two screws holding the burner control switch to the front panel, removed the wires from the old switch one at a time and installed them on the new switch. secured the new switch to the front panel, put the four screws back into the front panel, and closed the oven door. Real easy repair.

Removed two nut screws (accessed with oven door open) with nutdriver, panel dropped out. Transferred wiring one-by-one to new switch, removed old switch with allen wrench, installed new switch, replaced panel. Done! However, the problem is not corrected and all other possibilities have been explored with no solution in site. Ideas needed.

simply remove and replace th switches using a screw driver an a pair of needle nose pliers

Un screwed the two screws in the downdraft section enough to release the unit that holds the surface burner controls.Then removed the control nob, unscrewed the two screws that holds the switch in the unit, removed the wires, making sure the color of the wires were placed on the same contact point. Put it back together and it worked
fine.Of course I did shut off the power before starting any of the above

easy enough. Before you start, draw a picture of where the wires go on the old switch ( or take a picture).

Replaced the control.

It was easy enough I unplugged the stove. removed the screws under the control panel,removed the panel, removed the two screws holding the switch in place. moved the electrical wires from the old switch and placed them on the new switch. put it all back together in the reverse order.
it took greater than 15 minutes as this is the first time I did any work on my stove and wanted to be careful and not dismantle too much or scratch anything.

Changed out surface burner switch.Unscrewed two screws, changed plug onto new switch.Don't forget to turn off power!

Opened the back of the cooktop and found upper right element control switch burned. I removed the retaining screws and wires and spent two weeks chasing the switch at a local dealer. Found exactly what I needed at PartSelect.com and paid less even with shipping than at the local. Installed the switch with original screws and presto!! it worked.

Looked up schematic. Removed 3 screws holding cover. after I shut power off of course. Took off knob. Oriented new control to the one on panel. Disconnected each wire one at at time and immediately attached it to the new control for each wire. Removed screws holding old control and inserted and screwed to the new control and put the knob back on. Put the cover back on. Worked fine. Probably should replace the others as they don't turn as easily as the new one. Probably will spray some contact cleaner which will give me a few more years.

Remove 4 screws that holds down panel;removed dial;removed screw that held switch to panel. Took off wire one at a time ann put on corresponding lug. Repeated above in reverse.

switch power supply off at breaker panel

unscrew control box assembly from stove

slide control out of stove

unscrew burner control out of assembly

transfer wiring from old control to new in same relative location

reassemble in reverse order

restore power

test burner in all positions

We unplugged the range from the wall first so as not to get electrocuted. We removed the face of the control panel by removing the screws and 2 hex nuts underneath that hold it in place, and removed the trim. Then we disconnected the malfunctioning control switch, taking note of what order the wires go in. Hooked the new switch up and popped it through the face of the control panel. We then put the trim back, and reattached the control panel with the screws. Very easy!!