C101-C Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Shrub Oak, NY
- Parts Used:
- W11120795
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The burner switch was broken
The repair was easy. First, I turned off cooktop circuit breaker. Then, removed the burner switch panel and the nut securing burner switch to panel. Disconnected the wiring and refit with new switch. Install switch panel and turned power back on. Now it's time to cook some dinner. Let's eat. :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria from Nashua, NH
- Parts Used:
- 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
Burners Didn't Work
After a long time being without a working stovetop-an electrician friend said we needed to change a switch-it was ordered and came very quickly and installed-then it was determined that we needed a switch for the other side of the stovetop-I ordered it and got it the next day! It was a joy cooking thanksgiving dinner on a stove that worked-and I have a new friend that is interested in seeing me on a more regular basis. I know if I needed any kind of parts, I would check with partselect first ;)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Stewartstown, PA
- Parts Used:
- W11120795
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The switch on my cooktop broke from extreme age and ossification.
I purchased a replacement. I unplugged the cooktop. Unscrewed the little instrument panel and pulled it out. Turning over the panel, I noted the wires to the switch and photographed them in case I need to check them later. I pulled them off of the old, broken switch and put them onto the new switch, one at a time so that I couldn't get them messed up. Once all of the wires were switched, I removed the old switch and put on the new one. I then plugged in the model and tested the switch. It worked perfectly! IMPORTANT: I then tried to slide the panel back into the cooktop but forgot to unplug it first. This was a huge mistake, causing a nasty flash of electricity and smell. I unplugged the cooktop, put the panel back in, and replugged the cooktop. It worked, fortunately. Moral: ALWAYS unplug the damned cooktop when working on it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn W. from Lake Charles, LA
- Parts Used:
- 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The metal parts of the switches that the control knobs fit on broke on three of the switches.
I removed the two screws holding the control panel in place with a Phillips screwdriver, pulled the assembly of switches up, and found the number on the old switches. Amazingly on PartsSelect's website I found a picture of the exact switch with the exact same part number stamped on it. I ordered three new switches, and they arrived two or three days later. I removed the wires from the old switch with a pair of needle-nose pliers, reconnected them to the new switch in the exact same places, and had all three of them installed and working perfectly in about 45 minutes or an hour.
Was this instruction helpful to you?
Thank you for voting!
Both burners would come on when you turn on the back larg back burner.
Replaced surface unit infinite switch
Was this instruction helpful to you?
Thank you for voting!
Broken surface burner
I can't believe I fixed the cook top in less than 30 minutes, including replacing the knobs and all pilot lens and now looks like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Coral Springs, FL
- Parts Used:
- W11120795
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken switch
Turned off 50 amp breaker. Removed knob, unscrewed holding nut and unplugged each of five wires from broken switch and connected wires to new switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Llewellyn P. from Junction, TX
- Parts Used:
- W11120795
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Jennaire 4 burner stove top right two burners coming on full heat with either controls.
Read privious fixes. Didn't know which control was bad but ordered two new ones. Marked locations of switch contacts and wire colors. Removed old controls. Installed new replacements and everything works fine. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Lakeville, MA
- Parts Used:
- 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The heat would not stay on keep heating up and turning off with no low heat
Unfortunately it was the wrong part I replaced the infinite switch and had the same problem so I am still trouble shooting but I plan to continue to use parts select they are excellent to work with and very quick to deliver parts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gina from Oak Harbor, WA
- Parts Used:
- W11120795
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
A burner on the cook top stopped working
I switched the circuit breaker off at the electrical panel, removed the burner switch assembly (two screws) from the cook top. The burner switches are held in place by a single nut over the control stem. I unscrewed the nut from the failed switch, disconnected the four electrical leads (one by one) from the old switch and connected them in the same position on the new switch and replaced the nut. The clips on the electrical leads were oxidized/tarnished so I cleaned them with emery cloth to assure good contact with the posts on the switch. Replaced the burner switch assembly in the cook top, energized the circuit and the burner works perfectly again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- I R from Montgomery, TX
- Parts Used:
- W11120795
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Faulty infinite switch
Turn off the power!!! Remove two screws from back of switch section and pull toward you. That was the tricky part; it wasn't obvious to me how to remove the section. Then simply revmove the witres from the old switch one by one and put them on the new part. Close it up and you're good to go.
Was this instruction helpful to you?
Thank you for voting!
stem on burner controls broken
follow the EASY to read and understand instructions.replaced all 4 controls in about 35 min.
Was this instruction helpful to you?
Thank you for voting!
bearing went out in blower motor
removed old motor from cooktop & motor housing & replaced w/ new motor & parts to install same. parts needed where screws & isolators (3).All went ok
Was this instruction helpful to you?
Thank you for voting!