C236B-E Jenn-Air Cooktop - Instructions

First the power to the cooktop was turned off. Two screws were removed to be able to lift the fan switch holder. The old switch was removed easly because it fell apart. The nuts holding the part in broke as they were removed so they could not be reused. The new switch was put in place however the nuts were too small. I don't know what they were supposed to fit but not these screws. The part was super glued in place. It works perfectly.

The door came off easily after I removed the two hinge covers that are attached to the oven. Taking the door off can be done with one person but ideally two.

The new parts fit in perfectly and the hinge pin used for shipping comes out easiest with a pair or wire cutters (you do not cut it just grab it and pull).

After that, re-assemble the door and drop in place. It was a snap.

FYI...the shipping was ultra fast and the price was great.

No issues whatsover with the entire process.

We unplugged the range from the wall first so as not to get electrocuted. We removed the face of the control panel by removing the screws and 2 hex nuts underneath that hold it in place, and removed the trim. Then we disconnected the malfunctioning control switch, taking note of what order the wires go in. Hooked the new switch up and popped it through the face of the control panel. We then put the trim back, and reattached the control panel with the screws. Very easy!!

Disconnect power cord first. I remove the air fan cover to get to the two screws which hold the fan switch and burner knobs. Remove burner knobs and and remove switch cover, disconnect wires to fan switch. Pry spring nuts off with screwdriver to get switch off. Pay attention to which way switch goes on so that it turns on in the right direction. Install spring nuts (they may look too small but they're not) using a deep small socket the size of the spring nuts tap the the socket with a small hammer and the nuts will be locked in place. Put everything back in place and your done.

I remove fore screwsfrom the front panel. Then remove two screws to remove the switch and removed the wire plugs then put everything back together again.

2 screws to remove
disconnect 220 v power
use long nose pliers to transfer 5 female spade terminals
use nut driver to r@r shaft nut
replace panel with 2 screws
Turn on power and test!---OK!

Remove and replace grease filter.

very easy - not really a "repair" more of a face lift, although the grill was unusable.

Parts were perfect - Used it the same night.

Pulled the old one out & inserted the new one. Less than five minutes.

Replaced one of the four burner control switches on my Jennair cooktop. One of the tricks I use to prevent mistakes is putting the new switch along side the existing one and swap one connector at a time over to the new switch preventing any confusion and negating any need to mark the wires. This differs from your video assistant who disconnected all the wires at once.
gc.

We replaced the burner grates, knobs, air filter and burner pan. Looks as good as new!

I've ordered parts from you twice now, and both times the service has been absolutely amazing!!!!!

Now, on to how I did this without fire or electrocution:

Turned off breakers.
Grabbed a beer.
Removed two screws holding in plate.
Removed electrical connectors.
Removed two screws holding switch.
Put new switch in place with screws.
Reattached connectors.
Reseated plate & screws.
Turned on power & tested.
Finished beer and felt very manly.

The hardest part was getting the plate to re-seat.

Removed old filter, dropped in the new one.
(This really was not a "repair")

This was a no-brainer: old filter out, new filter in. In addition to replacing an old, greasy filter, I found that the exhaust fan now draws cooking fumes much more efficiently. So why did I wait the 6 years since we moved into this house to do this???

Not much to tell about installing a new grill grate.
Partselct.com was very prompt and efficient in sending out the part.