Models > JGC9430BDB > Instructions

JGC9430BDB Jenn-Air Cooktop - Instructions

Jump to:

All Instructions for the JGC9430BDB
31 - 45 of 59
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
James from PRATTVILLE, AL
Parts Used:
74007734
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Electrode not working.
Removed two screws and slipped the electrode connection off. Then reserved the process.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John L from FAIR OAKS, CA
Parts Used:
74007735
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
the gas burner head needed to be rerplaced due to the sparker not functioning properly
Ordered a replacement, removed the old burner and installed the new one. Works perfectly.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bill from Rochester, NY
Parts Used:
WP74007749
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
I lost the cap
after I received the cap in the mail, I removed the grillwork and set the cap in place. then replaced the grill and my wife fixed my supper.
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
james from neuvo, CA
Parts Used:
WP74009336
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Ignitor cracked on 3 of my gas top buners
I used a star head driver to take of burners ,then pulled wires out about 2 inches unplugged old ignitors and plugged in new ones
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Cresco, PA
Parts Used:
WP74009336
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Range would not light.
First I removed the burner, two screws held it in place. The ignitor is attached to the burner with one screw remove the screw then remove the one wire connection. Reverse the steps to put back together. The whole job from start to finish takes about five minutes.
1 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ed from Overland Park, KS
Parts Used:
WP74009336
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
The ignitor went out on one of the burners of the gas range
Remove the burner cover to reach the burner assembly. From the top of the cooktop you will see 2 screws holing the burner assembly. Using a T drive (6 point screwdriver)remove both screws and the burner assembly will come out of the cook top. Using a phillips head screw driver, remove the old ignitor from the burner assembly. Mine was galled up, so I had to use some penetrating oil and let it sit for a half hour. I then used a hammer and a phillips head screwdriver to tap the screw as I twisted to un-tightened the screw. Once it broke loose, I placed the new ignitor and reassembled the burner into the stove.
1 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
frank from flushing, NY
Parts Used:
WPW10168628
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
knob melt do to heat
chang knob
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
frank from flushing, NY
Parts Used:
WPW10168628
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
burnt knob
changed knob
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
ned from leland, MS
Parts Used:
WPW10475147
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
would not light
remove two screws then unplug the wires put the wires back on the new one
2 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from Hendersonville, NC
Parts Used:
WP74009336
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Ignitor cracked and would not light
Simply removed the old ignitor and install the exact replacement part. Work great.
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Douglas from La Habra, CA
Parts Used:
WP74009336
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Broken electrode
First I tried twitching my nose....after I stopped sneezing I got a screw driver and put the new electrode in and gosh in gahiggy, it worked!!
1 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Charles from Buena Park, CA
Parts Used:
W11087445
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Wrench (Adjustable)
Gas explosion due to bad Gas Pressure Regulator
First step is to turn gas off to cook top and also disconnect power to the unit. Than using a crescent wrench disconnect the gas line going to the unit from the Regulator. Than again using the crescent wrench disconnect the regulator from the bottom of the unit. Next remove the nipple that connects the gas line to the regulator from the old unit. Apply new pipe dope to the threads and screw it into the new one and tighten down. Next install the regulator to the unit and install the gas line to the regulator. once done with the install you can now plug the unit in and turn on the gas. You are now ready to use the cook top again
5 of 21 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
grant from aurora, CO
Parts Used:
WP74009336
Difficulty Level:
Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Spark Ignitor replacement
Screws holding burner base and ignitor were plain steel. If they had been stainless they probably would not have rusted in so tight. One in the base broke off, and the one holding the ignitor could not be removed, even with heat from a torch. I ended drilling it out and re-tapping the hole. If I wasn't mechanically inclined I would have had to give up and order a new burner base.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Earl from Iuka, IL
Parts Used:
WPW10154101
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Burner Head was leaking gas from side
I lifted the burner tray from stove turned it upside down then removed six small screws from side of cover pan then I removed the cover then I removed the screws from the back of the old burners and igniter.Then I turned the old burner counter clockwise and it lifted out easly. the igniter is removed with no problem. The new burner is put in place and turned clockwise to lock in place.Then replace then the gas tubes and igniter and igniter wire then put tray cover on.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tom from Two Rivers, WI
Parts Used:
WP74009336
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Igniter Needed Replacement
Removed the burner & igniter as a unit. Screws holding burner down were very tight. One came out with effort, the other one the head broke off. Tried heat but to no avail. The screw holding the igniter had to be drilled out. Fortunatly I work in a machine shop so I was able to remove the screw, but the hole was then too large for the replacement screw. I wound aluminum foil around a toothpick to form a bushing in the hole so the screw could grab. Same principle as those plastic anchors for plaster or drywall. Bought stainless screws, but did not even try to get the broken screw out of the cooktop. The one screw holds it in place just fine. Wife is very happy.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JGC9430BDB
31 - 45 of 59