2325ERS Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
install burner drip pans
Did not need tools for this job. Simply lift burner element and remove old drip pan and put new one in its place. However - the drip pans that were shipped only fit on the left side of the range. The right side, where the grill attachment goes, is so shallow that the drip pans on that side hit the bottom plate beneath the burner element and would not let the element go down far enough to seat properly. I kept the two pans that don't fit for extras, but I still need shallower pans to fit on the right side.
Was this instruction helpful to you?
Thank you for voting!
worn out parts
Everyone was amazed we could still get parts for our 25 year old Jenn-air stove top. Easy installation, hands only, couldn't be happier with the easy of ordering, the fast shippment, the quick replacement. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yong from Houston, TX
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Change the Oil/Grease Filter
It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Royce from Garland, TX
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knobs were worn badly
Pulled off old knob, then pressed on the new one.
It was very easy, and the part was the correct one.
It was very easy, and the part was the correct one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from NEENAH, WI
- Parts Used:
- WPY700854
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Numbers on surface burner knobs were illegibel.
I also sprayed them 3-times with a clear coat before installing. The clear coat I purchased at WalMart once I noticed it claimed to be safe for plastic. Avoid a clear lacquer based product.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christy from MOLALLA, OR
- Parts Used:
- WPY700854
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
All four knobs were stripped
We cleaned the rod on the stove and pushed the new knobs into place. This Jenn Air range was made in 1980. Nice to know Jenn Air is still making parts for their ranges. We also ordered new coil elements which fit perfectly size 6 inch and 8 inch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- beatrice from TUCSON, AZ
- Parts Used:
- WPY700854
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burner knobs were wearing out, metal rims were falling off.
Just slid off the old burner knobs, and pushed on the new ones. The most difficult part of the whole thing was just being sure that I ordered the correct knobs that used a D fitting. I ordered some a year ago that weren't the correct fitting.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynne from Weatherford, OK
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
my old knobs were so worn that I couldn't see the numbers
I had tried several other "universal" brands from the home improvement center but nothing worked with my Jen-Aire. I finally ordered from PartSelect and they fit perfectly! My range-top looks brand new and finding and ordering the correct parts was amazingly easy. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from Chapel Hill, NC
- Parts Used:
- 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Rear burner always high, ignored temperature setting.
Turned off breaker for range. Removed 4 phillips screws on control panel, tipped it forward and rested it on top of partially open oven door. Removed knob and nut on old switch. Moved wires, one at a time from old to new switch. Put new switch in place, tightened nut and pushed on knob. Put control panel back in place and installed 4 screws... piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from THE WOODLANDS, TX
- Parts Used:
- 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Broken knob dhaft
Replaced wires from broken to new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Bloomingburg, NY
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
knobs were getting hard to read.
Pulled old knobs off, pressed new ones on. Probably well under a minute for 6 knobs. Anyone with the IQ of a horseradish could have done it. But what was really great was the help and personality of the agent at the other end of the phone. Shipping was as promised, and the entire experience was delightful!
Was this instruction helpful to you?
Thank you for voting!
Could Not Use One Burner
Turned power to stove off. Removed two screws from cover - lifted cover up and pulled switch out and disconnected wires. Put new switch in and connected wires. Made sure that it was in correct position by placing knob on to make sure off position was correct - then placed plate in position and closed - put two screws back on plate and put new knob on. Turned power back on and turned knob and burner back in operation
Was this instruction helpful to you?
Thank you for voting!