JEC9536ADS Jenn-Air Cooktop - Instructions

Take old off and put new on

Cut power to range in breaker panel. Then removed two screws (1/4" nutdriver) or phillips head just under top in front. No need to move range out from wall. Once those two screws were out, I lifted the top carefully (since wires are attached to back of range) and propped it up with a piece of spare lumber I had lying around. Then removed two screws holding right rear burner, and doing one wire at a time, pulled the wires from bad burner and reattached wires to new burner. Oh, I did need some pliers to pull the wires from the old burner; they were on real tight. ALSO, the old burner had a series of numbers around it. I quickly learned that these helped you line up the burner correctly. So I noted the numbers with the screw holes in the old burner and made sure I used the same number holes in the new burner. Once new wires were attached, I attached the new burner, aligning the same hole numbers as the removed burner, and everything lined up perfectly. Two screws were inserted to hold the burner. I lowered the top and reinserted the two screws under the front of the top and I was done. Total time was about 13 to 14 minutes. Honestly, very easy. Plus prior to me taking on the project, I had called a Maytag repair shop, who said their fee was $99, plus parts, plus any extra time required for labor, but the latter was not likely something that typically occured.

the cracked knob left the round piece of metal that is part of the knob inside the stovetop, preventing the new knob from being installed at the right height. We were able to remove the metal piece and place the new knob on at the correct height. We were very pleased at how fast the part was received.

bought new ones and pushed them onto D shaped posts total time 90 seconds they may break again in 10 years but I am to lazy to reinforce them

I used a nut driver to take the module apart. When I discovered the problem I simply threw the module out but kept the ceramic top and then ordered a new stove top. The burners would be a snap to install if the clips that secure it in place had not ALL broken off. All you do is pull the wires off with a pair pliers and set the new unit in place and reattach the wires. All that would be left would be to reattach the ceramic top and set the module back into place on the stove top. The modules were discontinued and no longer available any place. Believe me I tried. The delivery to me from Parts Perfect was very quick and without any hassles. I had no problem returning the burner. I would recommend these people any time.

I unscrewed the glass surface from the bottom portion where the element lays. I gently unplugs the element and plugged in the new element. Then screwed it back together.

I lived with a burned out element in my smooth top cooktop for a couple of years. When the second large element burned out, with a house full of weekend guest coming, I decided I had better do something. Checked out PartSelect, found the replacements. I am a 73 year old grandma. My grandson and I replaced the elements within 20 minutes and we were cooking for 16 people. Woo Hoo! Removed eight screws lifted off the glass top, removed two electrical clips, removed the old element and reversed the process X 2. Great company to deal with, fast shipping and I love the tutorials. Since August, we have repaired our old dishwasher and gas dryer. All with parts from PartSelect. Thank you PartSelect.

Shut off 220 volt power to range. Removed two screws for cooktop element access. Used needle-nose pliers to remove power (2) and control (2) lugs and wires. Remove defective cooking element module, replaced. Reverse steps for new unit.

Pushed the knob down on the spindle. Second order in three years.

The original knobs were poorly made and kept braking. After the third set, which were very expensive for some plastic knobs, I read this web page for help. Based on what I learned and what I read, I glued the metal sleeve in the knob shaft with some super glue. I then wrapped the shaft with copper wire and spread some industrial glue over the copper wrapping, which looked like a spring around the shaft. I have had no problems in the last month. I hope it keeps up.

We replaced the control knob with an exact replica from PartSelect at a very reasonable price – Thank you.

remove knobs from pkg, remove broken knobs from range insert new knobs wallah done.

i did fine

Removed the two screws, on both sides of the oven wall corner. Gently lift the front end of the glass top and pull towards me and disconnect the two electrical sockets. Carried the glass top assembly on the kitchen table and turned upside down. Removed the six screws. Removed the assembly from the glass top. Turn the top burners assembly over and disengaged the two clips of the burned out burner from the assembly plate. Transferred the two clips to the new burner on the exact locations like the old ones were. I have placed the new burner on the location and snapped the clips on the slots. Removed the connectors one piece at a time and connected to the new burner. Reversed the previous disassembly and all was done Works like a charm. Thank you all for assisting me in providing the necessary parts and video instructions. It was a lot cheaper than to buy a new range.

Lifted the range top about 2 1/2 inches, removed the ceramic top and replaced the burner. Tested the burner before replacing the top. Everything worked fine.