CCG2421W Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- tao from Frisco, TX
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the shell if the igniter was broken
find the part (image is really helpful), buy, and replace. Like I said, it's really easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn Truax from Key West, FL
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
All the burner caps had badly rusted; tip-off was the smell of gas.
Our handyman took off the burner caps and checked after we reported smelling gas. We ordered the replacements here, and they arrived by only the 2nd business day, instead of 3-5 as expected. The only hard part was scouring off the rust, with SOS pads, from the stove top before putting on the new burner caps (a simple plug-in)!! This is very important to check on your stove; you could blow-up your house! The gas was escaping under the old burner cap, through the rusted-out portions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kenneth from brooklyn, NY
- Parts Used:
- 74004053
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
burner very hard to get out
Used strap wrench to turn out. Rust build up under the burner. Used flat screwdriver to loosen under burner and strap wrench to turn out. Then replaceing the igniter was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jon from western springs, IL
- Parts Used:
- WP74001385
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
knob was burned and needed to be replaced
just put it in place.
your company was used beacuse they had the part.
delivery was prompt.
your company was used beacuse they had the part.
delivery was prompt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from Hollister, CA
- Parts Used:
- WP74001385
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
I had broken knobs.
Pull off the old one and put on new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Wheaton, IL
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The burner would not lite. There was an intermittent spark from that burner.
Your site was easy to navigate, which made determining the problem from other customers easy, and choosing the correct part to replace the malfunctioning burner.
The malfunctioning burner was easy to remove by twisting it a quarter turn counter clockwise, removing the two wires and replacing it with the new burner cap with electrode.
The malfunctioning burner was easy to remove by twisting it a quarter turn counter clockwise, removing the two wires and replacing it with the new burner cap with electrode.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dmytro from Brooklyn, NY
- Parts Used:
- 12001596
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
It didn't spark fire
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the six wires. Then I repeated those steps in back order. That's it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Georgetown, TX
- Parts Used:
- WP74001385, 12001596
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Stove lighting feature failed
Removed stove top to work bench'
Disassembled burners from enclosure to gain
access to spark module.
removed old module and disconnected slip on electrical connections
Installed four new slipon connectors to match new modual
attached newmodule to frame and connected wires.
Tested unit by pluging into electeic outlet and turning burner dial to lite . Success
reassembled stove top and installed in kitchen.
job complete
Disassembled burners from enclosure to gain
access to spark module.
removed old module and disconnected slip on electrical connections
Installed four new slipon connectors to match new modual
attached newmodule to frame and connected wires.
Tested unit by pluging into electeic outlet and turning burner dial to lite . Success
reassembled stove top and installed in kitchen.
job complete
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Fort Washington, PA
- Parts Used:
- 12001596
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
no spark
Removed screws from back right of oven. Found spark module under right side panel of oven. Module connected in a slightly different way, so I had to drill a new hole and use a machine screw to secure it. All wires matched up exactly on new spark module. Replaced side panel, plugged it in and... SPARKS. Cheap and easy replacement and didn't have to call Maytag for repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Errol from Bay City, MI
- Parts Used:
- 12001596
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No spark at the burners
Replaced the ignition module with one from PartSelect. took care of the problem. They had the part in stock. Great service. Got the part in four days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from stratford, CT
- Parts Used:
- 12001596
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
turn on stove no spark to ignite the flame
I used the advise given in the website and it was very informative- the part was exactly where the folks on the website said it would be and although it wasnt the actual maytag part it was easily fitted by using the wire splices i mentioned and it was shipped quickly The whole process took less the 30 min once received. thank you for a very useful site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ZHENG from PINOLE, CA
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
repair range burner
in and out in 15 min ,is easy when part fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from South Burlington, VT
- Parts Used:
- 74004053
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Burner igniter was not lighting the pilot. Needed replacement.
We replaced 3 of 4 igniters on the stove top according to the previously submitted recommendations. Easy to do butt after putting one of the modules back together, we found one igniter still didn't function. We discovered the solution was to run the connecting wire under the gas tubing. Apparently it was compressed when it was over the top of the tube and not under it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Shelley, ID
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broke the insulator on the ignitor while cleaning the cooktop.
Unscrew the bottom cover, remove the old ignitor. Reverse the process to install. Hardest part was getting the bottom cover screws out because of rust. Otherwise, very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bhavni from Richmond, TX
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Burners won't light up
We received the burners we ordered in timely manner, and it was very easy to install. Just unhook the old burners and drop the new ones in and connect.
Was this instruction helpful to you?
Thank you for voting!