CCR467B-C Jenn-Air Cooktop - Instructions

The front burner the large one was burnt out, I cook alot so I need it, I happen to see a appliance repair man next door. I describe problem and he said well figure about 250 - 300 hundred dollars. 80 For the aprt the rest labor and house call. Well I looked at the booklet and figured out what I had to do ,needless to say I owent to your website and you had the exact part I needed and saved me alot of money. I sugest to d. I. Yers try it and if it doesn't work then call the repairman. Thank you parts select. Glenn voight

first removed 3 screws in front of the range then lift up the top glass and removed 1 screw that is holding the element and then disconnect the wires that are connect on the element then put the new element on place and wired it test it and works good

simply took off smooth surface top flipped it upsde down on a towel. unbolted the entire burner assembly. matched connections with the new burner with limit switch. replaced smooth surface top plugged it in. no problems. extremely easy fix no repair charges.

Exact fit, but read the instructions! Male connectors on element are labeled 1A 1B 2A 2C, very faintly etched in the ceramic. Even though the old and new elements look the same (and I took photos to aid installation), the connector locations are different -- 1A on the old element is where 2B on the new one is, etc. Used included extension wire for one that would not reach with the new configuration and everything works perfectly.

First, the diagram on your website said remove two screws. The diagram looked like they were on the back of the stove on each side. On my stove there were three screws that were visible under the front lip upon opening the oven door. I removed the top, which comes completely off and set it aside. Be careful when removing the top. Don't drag it out, otherwise you'll tear up the asbestos around the other burners. Two people would be better for the inexperienced people. The new elements have been redesigned, so the diagram doesn't fit what you are looking at. Plus, the diagram on paper is looking underneath the element when you are looking down on the top of the element. I removed one wire and put it in the same spot on the new. Turned out it was not the element that was bad. It was a loose wire in the inside of the control panel.

Turned off power to cooktop and double checked
Lifted up entire cooktop and rested it on two pieces of wood that spanned gap underneath
Removed screws from around edges to free the metal framework that holds the cooktop in place-- this requires spinning the cooktop a bit to get access to the back.
Lifted metal framework off
Lifted glass from cooktop off
Checked configuration of power plug ins against new part and noted where they should go. There was a slight difference of how plugs were arranged, but it was easy to logic out.
Removed old burner unit and plugged in new one. Ensure that nothing was touching contacts.
Replaced the glass top onto cooktop
Put metal frame back in place and screwed in
Lifted entire cooktop, removed boards, and lowered back into place

Turn Circuit breaker off.Open the Oven door removed the 2 screws to the top surface. Disconnect the wire harness mark and remove the wires from the Old Element, removed the screws holding the element to top surface, Remove element replace with new element. Install wires, install screws, reconnect wire harness reposition surface. Reinstall screws and turn Circuit breaker power back on. Done and Done

Remove three screws underneath bottom front edge of the range top. Bewteen the oven door and the range top. Lift rnage top up in frotn and prop up. Remove two screws o the element and replace. Found out the problems was not the element but the control switch. The heating element for the bimetalic control was brokened and not making contact. Element was ok. Would advise inspecting and using a dvm to check resistance of the element before purchasiing. By the way I swapped the control switch from another element and found out that they are claibrated to the sixe of the element. You have to purchase the right control switch or the element will not heat correctly.

Removed unit from counter, removed 14 screws holding glass top to frame, removed ceramic element, swapped over mounting brackets to new element, checked wireing as per instruction sheet (direct replacement) connected wires, re-installed glass top to frame and placed back into counter. ops check good.

turned off power to stove top..lifted unit out unscrewed top and switch had 2 screws re-placed switch and put back together.. make easy $100 plus switch

I removed the glass top and replaced the switch unit successfully. Hardest part was removing the unit from the countertop and bracing the base with a 4x4.

Knocked breaker removed stove top from iland removed a dozen screws replaced switch put screws back in installed top back in iland put breaker back in worked purfect.

Removed the cook top from the counter. Removed the switch housing and then the switch. Found a match and ordered. Part came in 2 business days. Once I put together the housing and connected the wire housing the burner worked perfect. The downdraft fan remained on. Placed a call to Jenn Air service and was asked to disconnect the fan switch. There must be some memory in the solid state portion of the switch. After a few mins I replaced the fan switch and hooked up the wiring. All worked fine.

Removed two screws holding cooktop to oven. Unlike the video, the cooktop was not detachable as the wires were hard-wired to the range, so I had to prop the top up with a 6" block of wood and was working upside down. I replaced the element and everything worked just fine.

We lifted the glass top, uninstalled the old burner and installed the new burner in it's place. It worked right away - and is still working. No other tricks the new burner was a perfect fit.