CG206B-E Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Max from Plano, TX
- Parts Used:
- WPY704512
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The right rear burner ignition switch malfunctioned.
Repair is simple as long as you TURN OFF THE CIRCUIT BREAKER first. After that, take off the cover over the switches (pull knobs off, remove 2 screws and lift off the cover), pull the bad switch straight up off the gas valve, pull the two wires off the switch, plug them back onto the new switch, place it back over the gas valve stem, reassimble the cover and knobs, turn back on the circuit breaker, and verify that ignition switch works. Not a hard repair. (HINT: while you are waiting on the replacement part, you can light the bad burner by turning on the opposite burner ignition switch and using that "spark" to light the other burner.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Fremont, CA
- Parts Used:
- WP74008014
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven Door wouldn't fully close and light stayed on.
Remove oven door by removing chrome flat plate that holds the hinge in place (one screw at each hinge) and LIFT door off oven. There is a hole in the hinge that you can stick a small nail through to hold the hinge in the "partially open" position for easier removal and replacement of the door (I didn't know this until I received the new hinges, which have a removeable pin in the hole.) After door is off, remove three screws each, on the top and bottom of door, to remove the back half of door and expose the hinges. Remove one screw from bottom of door that holds bottom of hinge in place. Lift out hinge bottom and unhook top of hinge. Reverse process to reassemble. Remove small pins by opening oven door fully. The new hinges did solve the problem. You have to order two hinges for each door. They are NOT sold as pairs.
Was this instruction helpful to you?
Thank you for voting!
Jammed gas valve , bad fan switch, and corroded ignitors
Turned off the gas valve and disconected the gas line from the stove-top. Removed the stove top and disassembled the unit, to access the bad parts. While unit was disassembled we cleaned the parts which were to be reused and applied the new parts. The unit was then reassembled and reinstalled. The replacement of the gas valve required only a 1/2" wrench and screw driver, while the replacement of the ignitors required the use of an adjustable wrench. The ignitors are connected via spade connectors to an electrical device located in the electrical box at the lower center portion of the unit. Not a hard job but slightly time consuming.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russ from Jacksboro, TX
- Parts Used:
- WP74008014
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven door hinges broken
Removed the door then the end caps and inner panel then the hinge system and replaced with the one piece new set of hinges and back together done in 30 to 45 minutes The new parts were a perfect replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Santa Rosa, CA
- Parts Used:
- 3401X055-09, WP7505P283-60, 12200030, 74005189
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Replaced the griddle side with 2 burners
Not a problem, very simple once I got all the parts I needed...operator at partselect was very helpful and nice to talk to...Thanks for the extra cooking space
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louise from Cedar Rapids, IA
- Parts Used:
- WP74008014
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
When opening the oven door, the hinge on the left of the door broke.
We panicked cause even simple repairs on these products cost and cost.....but we remained calm and ordered the exact part necessary from you. It arrived in just 3 days and once we had the part in hand it was easy to understand how to replace it. We disassembled the door with screwdrive and swapped the broken part with the new one. The one gotcha was that we were not aware of the shipping pin holding the spring and we struggled for a few trying to get the door closed all the way. Once we discovered the pin and removed it, it was fixed and we were PLEASED!
Thank you,
Louise and Rickl
Thank you,
Louise and Rickl
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anaclare from Oak Park, AL
- Parts Used:
- Y712601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One part of the grill burner came detached, caused fire at the connection
I turned off the burner and allowed it to cool. I then checked the website for the part and also got a new grease filter and grill grate. When the parts came, I plugged in the new grill burner, replaced the grill grates, and dropped the filter in place. Total time was about 8 or 10 minutes--most of which was opening the packages. The grill burner is designed so that it can be removed and replaced with a standard 2 burner unit. No tools were needed. I was glad to find the parts for my 17 year old dual-fuel range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ALAN from OSWEGO, IL
- Parts Used:
- WP74008014
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven light stays on when door is shut.
I replaced the hinges as described in other posts and the problem was solved. When the oven was 2 years old it had the same problem but the hinges should not have fatigued at that point. The engineering problem someone mentioned is that the pin of the light switch is too short. I touched it with lipstick, closed the oven door, and opened the door to see exactly where the door touched the pin. I drilled a small hole in the door and screwed in a self tapping metal screw...problem solved for 8 years until the hinges fatigued. After replacing the hinges I tried removing the screw but the light stayed on so I put the screw back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Centennial, CO
- Parts Used:
- 12200030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My burner grate needed to be replaced
My husband threw a pot holder on the hot (not lit) burner grate.The potholder melted on the grate and we were not able to remove the melted fabric. We ordered a new grate and it looked so good we ordered three more. I am planning to replace the burners next. We'll have a brand new looking cooktop. The cooktop is 15 years old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Norcross, GA
- Parts Used:
- 12001129
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Exhaust Fan Switch broke so you couldn't turn the fan on.
I removed the screws that hold the escutcheon assembly in place and lifted it from the range top. I slipped the wire connectors from the old switch and removed the push nuts. Removing the push nuts was the most difficult part. I wedged a small screwdriver under them and made enough space to cut them off with wire cutters (DON'T CUT THE POLES THE PUSH NUTS ARE ATTACHED TO!). There may be an easier way to remove them, but I'm a rookie and don't know what the easier way would be.
I attached the wires back to the same poles on the new switch as they were positioned on the old switch and pushed on the push nuts that came with the new switch to hold it in place. There isn't much room to work with so I used a small socket from a socket wrench set to hold the new push nuts in place while I pushed them on. The push nuts I received with the new switch were really too small. I forced one on, but broke the other one. I bought another slightly larger one at my local hardware store and it worked great.
I reattached the escutcheon assembly and was back in business. Overall, it took me about 30 minutes.
I attached the wires back to the same poles on the new switch as they were positioned on the old switch and pushed on the push nuts that came with the new switch to hold it in place. There isn't much room to work with so I used a small socket from a socket wrench set to hold the new push nuts in place while I pushed them on. The push nuts I received with the new switch were really too small. I forced one on, but broke the other one. I bought another slightly larger one at my local hardware store and it worked great.
I reattached the escutcheon assembly and was back in business. Overall, it took me about 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Oak Grove, MO
- Parts Used:
- WP74008014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
replace door hinge
The repair was very easy to perform, but the springs in the new hinge were not as strong as the old one. The door would not close all the way unless you held it closed. The hinge looked identical but spring had less tension.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruno from Scottsdale, AZ
- Parts Used:
- WP74008014
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The Old Hinges broke off and the door would not stay closed
I removed the single screw on each side of the oven by the hinge to remove the hinge cover plate and expose the hinge opening. I lifted off the glass oven door up and out and set it on my work bench. The door is heavy because its glass so make sure the doors on the way to the garage are open to your work bench area. I installed the cover plates back on so i would not loose the little covers and screws. I removed the screws all around the door and set them in a cup and lifted up the inner part of the door and the hinges are exposed. After removing the screws that hold on the hinges it lifted right out. I cleaned all the glass and set the new hinges in and locked them down with the screws and installed back the inner part of the door to the outer part and returned all the screws back. I then removed they screws on the hinge covers. I did not loose them with 4 kids running around and lifted the door back into the hinge openings and pushed down and it locked in. I then put a little pressure down on the door and removed the little locking pins. I pushed the door all the down and installed the hinge covers back on and it works beautiful. I think the new hinges are better than the set that came with the Jenn-Air wall oven. Thanks Parts Select. Also the new hinges came in 3 days as promised.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from GAINESVILLE, GA
- Parts Used:
- WP71001641
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
old cracked
pull off old ,add new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- thomas from Goodrich, TX
- Parts Used:
- WP7505P283-60, 74005189
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
20 year old burners were slow to light and hard to adjust for our propane fired stove. And, they were scratched and ugly
Removed four screws; withdrew two burners; set two new burners in place; installed same old screws. That was it. When I turned them on to adjust the flame, they came on almost instantly and no adjustment was needed.
Wife loves the nice new look.
Wife loves the nice new look.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from HOLLISTON, MA
- Parts Used:
- WP7505P283-60, 74005189
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
Part arrived broken.
Contacted customer service via email. Included a description of the problem as well as a photo that clearly showed that the Front Burner Assembly was, in fact, NOT an assembly when it arrived.
Nobody even acknowledged my email.
This was a $140 assembly.
Never again will use these guys for repair parts.
Nobody even acknowledged my email.
This was a $140 assembly.
Never again will use these guys for repair parts.
Was this instruction helpful to you?
Thank you for voting!