JEC8430ADS Jenn-Air Cooktop - Instructions

first I checked continuity through the surface element (burner) switch (rheostat) which was fine. then found the screws holding the burner top on and removed, this made it possible to lift up the burner top and remove the burnt out surface element.which was easy to see. take down the number, buy a new one and re hook up the four wires to the new element. (always mark down where the wires went)

1. Remove power from unit. 2. Removed 1/4" sheet metal screw from lower blower vent tube. 3. Lifted the unit above the counter and placed two 1x2" boards between the unit and counter. To remove the Stove Top to get access to the Element you must remove 8 each 1/4" sheet metal screws from the bottom side of the Stove Top attaching flange. 3 each screws on the forward and aft side and 1 each on the left and right side. (Note, the 8 each 1/4" attaching screws are at the top of the Stove Top attaching flange.) 4. Remove the Vent Grill and locate the 2 each cross point screws on the center left and right side of the opening. (Note. Due to the limited space, I used a right angle cross point driver.) 5. Remove Stove Top. 6. Tag electrical connections. Remove and replace Element. 7. Turn on power and check Element. Remove power and Reassemble Unit.

My mother is a great cook that is always in a hurry ... and I know that she is not always pushing those plastic knobs DOWN before turning them. Frustrated with reordering these expensive plastic knobs,I decided to get smart. I reordered 6 knobs (this is the 3rd time in 2 years). These knobs are designed to break. I decided to reinforce the plastic that goes around the knob shafts. At first, I thought about using some rigid metal bird bands like on a parrot. I second thought that this would be too difficult to find the perfect size to fit the outside diameter of the knob, so I decided to buy slightly smaller diameter, tightly coiled, sturdy, steel springs to fit around the plastic that fits onto the shafts. I manipulated each spring to become slightly larger to fit over the plastic by twisting the spring in the direction of uncoiling it. Not permanently unbending it, but just enough to make it grow in diameter to fit around the outside. I clipped the excess wire from the spring with wire cutters and reinforcerd everything with a coat of good strong epoxy . It seems that the metal spring and epoxy bonded to the knob became SOLID AS A ROCK. I figured, if the plastic can't split from the D- SHAPED shaft, then we have a knob that is as good as if it were made out of metal.

I watched the video, purchased the correct heating element and did the repair as illustrated in the video. I simply removed the cook top, removed the ground wire, removed the wiring harness, removed the failed heating element, installed the new heating element and reinstalled the wiring. Piece of cake!

First I shut off the power to the stove top and the electrical breaker box. I found that the stove top was stuck to the counter top surface; a butter knife was used to break the old seal by inserting it under the lip of the stove top and slowly broke the seal by going all the way around the lip. Then I lifted the cook top out of the counter. I had to remove the entire sheet metal bottom enclosure for easier access to the switch compartment. I removed the 2 screws holding the old switch in place. I installed the new switch. Using the wiring diagram, included in the packaging of the switch, I labeled each connector with the proper colored wire, physically traced each wire to be certain it matched the wiring diagram. I removed the wires from the old switch, using a pair of needle nose pliers to prevent any damage to the wires, then connected each wire to the identified terminals on the new switch. Re-assembled the enclosure and removed the old foam seal. I replaced the old foam with the new foam. I then placed the cook top back into the counter cutout, turned on the breaker and turned on the burner. Wa-lah, every thing worked. Great job on the instructions. It made the job easy and straight forward. The only thing I found a little difficult was trying to remove the 2 screws holding the switch in place by only removing the small access to the switch compartment. It was much easier to remove the whole bottom enclosure. Just a few more screws, which took about 5 minutes.

Disconnect the power.took the cooktop off the range. Turned it over. Removed the underside plate. Disconnected the bad element. Pluged inthe new element. Replaced the under plate. Reconnected the range to the stovetop .put cooktop in place. Reattached screws. Turned on power. Worked perfectly.

First, I turned the circuit breaker off to the range. Then, I pulled the range out so that I could get to the screws which held the glass top in place. They were located on the sides of the range. I had to remove the trim pieces on the sides to get to the forward screws. Once that was done, I lifted the glass top, unplugged the wire harness, flpped it over on a protected surface. I noted the numbers on the old coil where the clips held it in place and put the clips on the new coil in the same place. The old wires just clipped on to the new coil exactly as they clipped on to the old coil. I put it all back together and it works great! I am a 70 year old woman who did this all by myself. You young guys should have no problem.

The part arrived right on time. My husband and son made the repair. Neither do electrical work but they read some "you tube" instructions and figured it out fairly easily. Our installation problems were with the way the unit had been installed in the cabinet and how the countertop was cut originally. Overall very good experience.

unscrew 3 screws under the control panel and pull that away from the glass top making sure the wires don't come apart from the connectors. care fully slide the glass forward and replace the burner which was the easy part. DO NOT try to test without making sure that none of the burner are touching the metal surface!!!!!!!! it will trip your breaker. But now we have a range with 4 burner after a year THANKS

i did fine

Removed two screws holding cooktop to oven. Unlike the video, the cooktop was not detachable as the wires were hard-wired to the range, so I had to prop the top up with a 6" block of wood and was working upside down. I replaced the element and everything worked just fine.

Repair video was very helpful. I have removed the screws on both sides of the appliance under the surface plate, in the front. The Owen door has to be open for that. Then I have pulled the surface plate for a little space to disconnect the two connectors. Turned the surface plate over on the kitchen table, removed the 6 screws. Turned the burners assembly over and removed the small burner by disengaging the two clips. I have removed the 2 clops from the burned burner and assembled it to the new burner. I have placed the burner and engaged the 2 clips with a crownose players. I have removed one electrical connecter at a time and connected to the new burner. I have turned over the assembly over the glass plate and assembled the back cover with 6 screws. Put the surface plate on the range and connected the 2 connectors, pushed back, lined it up with the 2 screw holes in front of the range on bot sides and put the 2 screws in and Finished.

The range top came off with two screws under the front portion of the glass top (by the oven door). I unplugged the connection plugs at the rear off the range top, unscrewed the rear screws holding the heating unit in place and plugged in new element and reassembled range unit. You need to removed the two phillip head screws at the rear of the range top in order to remove the bar holding the heating element. Once you do this it is very easy to finish the job.

Removed the two screws, on both sides of the oven wall corner. Gently lift the front end of the glass top and pull towards me and disconnect the two electrical sockets. Carried the glass top assembly on the kitchen table and turned upside down. Removed the six screws. Removed the assembly from the glass top. Turn the top burners assembly over and disengaged the two clips of the burned out burner from the assembly plate. Transferred the two clips to the new burner on the exact locations like the old ones were. I have placed the new burner on the location and snapped the clips on the slots. Removed the connectors one piece at a time and connected to the new burner. Reversed the previous disassembly and all was done Works like a charm. Thank you all for assisting me in providing the necessary parts and video instructions. It was a lot cheaper than to buy a new range.

Lifted the range top about 2 1/2 inches, removed the ceramic top and replaced the burner. Tested the burner before replacing the top. Everything worked fine.