C202 Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
surface unit infinite switch needed replaced. The knobs and lens were cosmetic.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wires and replaced the connections in sequence. It was easy. BUT, be sure the circuit breaker is disconnected if you want to enjoy the fruits of your labor. I figure I saved about $1100 by not having to buy a new stove top and I now have an almost new one. The cook appreciates it too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Starla from Tomball, TX
- Parts Used:
- WPY04100166, WPY04100165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replacement of elements
Simply unplugged the old elements and inserted the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynne from Weatherford, OK
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
my old knobs were so worn that I couldn't see the numbers
I had tried several other "universal" brands from the home improvement center but nothing worked with my Jen-Aire. I finally ordered from PartSelect and they fit perfectly! My range-top looks brand new and finding and ordering the correct parts was amazingly easy. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from Chapel Hill, NC
- Parts Used:
- 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Rear burner always high, ignored temperature setting.
Turned off breaker for range. Removed 4 phillips screws on control panel, tipped it forward and rested it on top of partially open oven door. Removed knob and nut on old switch. Moved wires, one at a time from old to new switch. Put new switch in place, tightened nut and pushed on knob. Put control panel back in place and installed 4 screws... piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from MAPLE VALLEY, WA
- Parts Used:
- 12200035
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
parts needed to be replaced
Hubby & I
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BETH from COUNCE, TN
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
burner receptacle failed (stove over 30 years old)
Took out burner (pulls out) Took out one screw that holds recep. in, cut the two old wires and attached new wires with wire nuts included in the new package.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRANCIS from MILLBURY, MA
- Parts Used:
- W11120795
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Right front burner switch burnt out
Shut off power. Removed screws holding panel.Removed wires from old switch.Installed wires on new switch and reinstalled panel.EASY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Owen B Douglass from BROOMALL, PA
- Parts Used:
- W11120795
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burn was full on or "high" at any switch position other than off.
Followed other's instructions from the web site: First - turned off the power at circuit breaker; removed two screws from downdraft vent area; pushed the switch housing back towards vent and lifted; held replacement switch next to defective switch and removed and replaced one wire at a time; loosed switch collar-nut and swapped defective switch for new one. Only issue was the "rat's nest" of wires gave very little room to work, especially if you have average sized hands.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melanie from SALIDA, CO
- Parts Used:
- 715396K
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Replace burnt out indicator light
I feel that the design of the indicator light, with the base attached to the bottom of the lens, is ingenious in that it eliminates the need for fasteners in that confined space, However, the plastic used for the base needs to be more flexible. Part of the base broke off in trying to force the base over the bottom of the lens. Fortunately, there was enough left on the base that I could slip it over the bottom of the lens and complete the installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christy from MOLALLA, OR
- Parts Used:
- WPY700854
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
All four knobs were stripped
We cleaned the rod on the stove and pushed the new knobs into place. This Jenn Air range was made in 1980. Nice to know Jenn Air is still making parts for their ranges. We also ordered new coil elements which fit perfectly size 6 inch and 8 inch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- beatrice from TUCSON, AZ
- Parts Used:
- WPY700854
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burner knobs were wearing out, metal rims were falling off.
Just slid off the old burner knobs, and pushed on the new ones. The most difficult part of the whole thing was just being sure that I ordered the correct knobs that used a D fitting. I ordered some a year ago that weren't the correct fitting.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert A from Farmington `, CT
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old Stove Top
Ordered new cartridges
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Alexandria, VA
- Parts Used:
- WPY04100166
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The radiant ring element had broken
Removed old element, plugged in new one, tested ok
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from THE WOODLANDS, TX
- Parts Used:
- 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Broken knob dhaft
Replaced wires from broken to new part.
Was this instruction helpful to you?
Thank you for voting!