C106 Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- gilbert from san antonio, TX
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
grill was getting red hot with out control
Followed instructions, once saw and how to replace and replug wires as the instructions it was easy as per your instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rex from Schaumburg, IL
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Switch inoperative
Remove cover plate, install new switch, replace cover place. Replace one wire at a time, a pair of needle nose pliers may be helpful. Surprise of this job was that I had a torque screw driver (I think that's what it's called) to remove the switch from the cover plate. These are the screws you'll see after removing the knob. Find that driver before you begin, mine was in the garage and for the life of me, I can't remember why I ever had one in the first place.
Thanks for a great web site!
Thanks for a great web site!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from CARROLLTON, TX
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
could not adj. temp. stayed high all the time
replaced stove top switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- S.. J. from Punta Gorda, FL
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Electric barbecue element not heating
1. Diagnosed problem = switch at fault not element
Made a diagram of wire positions on faulty switch
2. Ordered part = remarkable service! Switch arrived in less than 24 hours
3.Installed new switch
4. Tested appliance = success!
5. Saved $150 and a lot of aggravation
Terrific site. Excellent help in figuring out and solving the problem. Two thumbs up!
Made a diagram of wire positions on faulty switch
2. Ordered part = remarkable service! Switch arrived in less than 24 hours
3.Installed new switch
4. Tested appliance = success!
5. Saved $150 and a lot of aggravation
Terrific site. Excellent help in figuring out and solving the problem. Two thumbs up!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Birmingham, AL
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
bad surface burner switch
1. Turn off power at breaker. Take no chances. Turn on each working burner, fan, oven light to be sure there is no power to the appliance. Then, turn them off.
2. Pull knob on switch straight out to remove.
3. Remove 4 Phillips head screws under control panel. Pull panel gently down, then out toward you slightly to release top edge. Rest control panel on self-clean lock knob.
4. Confirm terminals on new switch match up with old switch.
5. Use needle-nose pliers to gently remove wires from old switch one at a time and place them on the
corresponding terminal on new the switch.
6. Reverse steps 3, 2 and 1. Test switch and burner.
2. Pull knob on switch straight out to remove.
3. Remove 4 Phillips head screws under control panel. Pull panel gently down, then out toward you slightly to release top edge. Rest control panel on self-clean lock knob.
4. Confirm terminals on new switch match up with old switch.
5. Use needle-nose pliers to gently remove wires from old switch one at a time and place them on the
corresponding terminal on new the switch.
6. Reverse steps 3, 2 and 1. Test switch and burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vanna from St. Johnsbury, VT
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Front right burner did not turn on
We followed the instructions on the video after receiving our part - they were perfect instructions and led us right through the repair. I have to say it would have been harder to do with one person - but probably doable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Two Rivers, WI
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Bad burnes off on switch
Easy as Pie.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Exchange, WV
- Parts Used:
- WP74008014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broken hinge
Took the door apart and replaced the hinge, very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norma from Salisbury, NC
- Parts Used:
- WP7772P007-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The paint begin popping of my original grill. My son had a friend that said that he could remove the old paint and repaint for me. Unfortunately in the shuffle of a motorcycle performance shop the grill was lost. I have been trying to get help from Jenn-Aire since March and they just kept saying th
Very simple for me!!! Open the box, uncover the new grill and lay it in its place.
Thank you so much!
Thank you so much!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Colette from Annapolis, MD
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed to replace the grease filter!
Followed the directions. Piece of cake!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Ashburn, GA
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rotten filter for down draft vent
How I did the repair is no consequence. The service of easily finding the part on your site is GREAT! and the shipping time more than reasonable! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Flower Mound, TX
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old yucky filter
Thanks, have been looking for a replacement for this dinosaur filter forever. It is great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Fort Walton Beach, FL
- Parts Used:
- 12001129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Downdraft switch on the top of the JennAir inkoperative.
I verified that there was current running to the switch.
Ordered a new switch,
Replaced the switch.
Had a little problem getting the oneway washers off the pegs but not much.
Saved the cost of a repair man and felt good about myself!
Ordered a new switch,
Replaced the switch.
Had a little problem getting the oneway washers off the pegs but not much.
Saved the cost of a repair man and felt good about myself!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Collegeville, PA
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Burner only operated on high, no medium or low heat.
First I moved the left rear burner to the right front. No change. Then I moved the burner units from left to right, No change. I guessed it was the control switch and ordered from PartSelect. Turnaround time from PartSelect was excellent.
I turned off the powerr to the range. Removed the screws holding on the front panel and then pulled the panel out far enough to see behind it. I located the faulty control switch and then held the new switch, next to it, and turning to proper orientation. I then, one at a time moved the wires to the new switch. After that it was mount the new switch, put the panel back in place and turn on the power.
I turned off the powerr to the range. Removed the screws holding on the front panel and then pulled the panel out far enough to see behind it. I located the faulty control switch and then held the new switch, next to it, and turning to proper orientation. I then, one at a time moved the wires to the new switch. After that it was mount the new switch, put the panel back in place and turn on the power.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from Irvington, NY
- Parts Used:
- WP7772P007-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The paint had chipped and peeled on the inlet grill
I lifted off the old grill and replaced them with the new ones. My stove top looks great again. If I could find them, I would like to replace the knobs to turn on the gas!
Was this instruction helpful to you?
Thank you for voting!