JEC9530ADF Jenn-Air Cooktop - Instructions

I had some confusion about the correct series number associated with my stove and called Partselect. They confirmed the part I was looking at was correct in less than 5 minutes. I then completed the order online. Even with standard shipping my order was processed immediately and I received the heating element the next day.

Turned off the breaker. Removed the two screws in the front holding the range top down. Loosened the screws holding the element in place while balancing the range top with my shoulder. Removed the wires from the older element one at a time and attached them to the new element. Put the new element in place and screwed back in place. If I had a little help with the range top I think I could have completed it in 5 minutes but I was at home alone and the other stories of doing this repair made it seem easy enough and it was.

looked for how to video on you tube. It saved me lots of money. Anyone could do it.

I ohmed out the burner element that wasnt working and found it was open. I ordered a new element thru PartSelect and installed it in the stove. I powered up the stove and turned on the burner but it didnt get hot. After a bit of testing I found that the new elements safety overtemp terminals werent in the same configuration as the original unit. I made some wiring adjustments and the burner was operating properly. Thanks PartSelect

Had this range for 6 years. My daughter turned on the burner and it went "pop". She was very upset. I found the best price at PartSelect, and ordered the same day.

the first burner arrived broken in the box. We contacted PartSelect, and they immediately sent another and rushed shipping. It arrived in excellent condition.

To replace the unit: First, I turned off the circuit breaker for the range. Then I removed the two Philips screws that held the cooktop down. Next I removed the nut screws holding the burner to the cooktop.

Then I placed the new burner next to the old one, and one by one swapped the wires (this way I was sure I had the right wire on the right connector). One of the wire connectors broke when removing it from the old burner. PartSelect had provided 4 repacement connector pieces (oddly, all of which were too small for the burner element). So I located a replacement connector at a local hardware store. Stripped the end of the wire and used pliers to fasten the new connector.

After all connectors were secured to the new burner, I screwed the burner to the cooktop, then closed the cooktop and secured it with the two screws.

Turned on the circuit breaker, and it works like new! Saved over $100 by doing it myself!

See description listed as problem

FIrst we found the power source ( this took us awhile) and cut the power at the fuse box. then we unplugged the cooktop and started to take out screws. It turned out the screw removal had nothing to do with the stove top coming out. We took the taping knife & pried it under a corner and lifted. the cook top was just sitting on the counter.
The hardest part of the whole job was holding the cook top because we did not disconnect the downdraft fan other than to pull the tape off the vent & fan. Now we could undo the rachet screws that held the glass top to the cook top & remove it.
Theburner was simply a matter of pulling connections loose & placing them on to the new one. The clips that hold the burner in place were removed w/ a screwdriver & replaced on to the new burner. Watch for the numbers on the burner underside to know where to reattache the clips. the unit that lights up to show that a burner is hot would not come off, but we managed to remove
the plastic part even though the clip screw would not loosen, and since it only had to float near by we used the unused wire included in the new part to hold it in place. Putting the unit back together was not too hard, but it took us a little while to get it all lined up. Be carefull of what ever you work on, the downdraft fan scratched up the counter top that we were working on. we started with cardboard under it & should have continued, we did not want to try & remove the fan. Then we put it back in the counter opening & plugged everything back in & to our amazement ( we are not handy people) it worked! the lights that had refused to work when one unit was burned out now worked on all four units. thank you partselect, we were able to do the repair with what you sent.

Ordered new knobs & now all burners work. Easy installation.

Removed 8 screws of retainer holding glass top to box.. Pulled 5 knobs and glass top and set aside. Popped 2 retaining clips holding burner , removed them and transferred to new burner (#12 and #48 position). Used wide blade screwdriver to facilitate removing terminals from old burner and attached terminals to new burner.Popped retaining clips into crossbeam, put glass top on and 8 screws back into retainer. Works great.

Ok this is a glasstop jenn air cce3531b, 5 burners, 11 years old. I am computer data entry employee and 56 years old. I have never done repairs myself in the past but decided to try. I ordered a new burner and indicator light as I wasnt sure which to replace. I found the main breaker and shut it off. I lifted the stovetop out of the counter opening by pushing it through the bottom and placed it on the counter with a towel under it, I had plenty of room to work so that was very easy. I used a nutdriver set to remove 12 screws and lifted off the top very carefully and placed it in the other room , since I had to repair unit thought I would also clean and replace the foam tape around the perimeter of the glasstop. Ok now I unscrewed 4 more screws with the nutdriver and replaced the indicator light, that took about 6 minutes so far. Then I turned the breaker back on and tested and it did not work. Turned breaker back off ,now I replaced the burner by lifting it out of the opening very easily, unscrewed with philips screwdriver 2 screws and the new burner was exactly the same as the existing one so I just slid the old connections off one at a time and replaced them as I went along onto the new burner, screwed it back into place and turned the breaker on and tested it and it worked. I now turned the breaker back off and took off the old foam tape from the glasstop and replaced with new, fit it back onto the base and screwed the 12 screws back in and placed it back into the counter opening and turned breaker back on and now all is fixed and I saved $100 dollars in labor fees. This took 35 minutes and was easy for me. Thanks you partselect

First I reviewed a video on YouTube by this site. Even though the range on the video was not the same as mind, it gave me an idea on what to do. I proceeded to pull the rang out from the wall and disconnected the power plug. Next I removed two screws from the back located on the left and used a flat blade screw driver to depress two brackets on the front to release the glass top panel. I unplugged the wiring harness and disconnected the grounding wire and took the glass panel off and laid it upside down on the kitchen table. I removed the old heating element first by unplugging the wiring and removing the brackets that held it in place. Installed the new one, plugged in all wirings, brackets, screws and replace the top back on the stove.

The repair was very easy. There were 3 screws under the front lip which had to be removed. This allowed the smooth glass top to be removed, tilt and pull forward. This exposed the burners and the unit I purchased was a direct replacemt for the burnt unit. All I had to do was remove the electrical clips from the old unit and put them on the new unit. There were 3 spring elements, each with 2 screws, which held the unit in place.

My grandson, age 15 did the replacement. Now, how easy is that!

I took the old knob off, got needle nose pliers to get the small steel sleeve off the post, and put the new knob on. The knob had a number on the underside, but it is not the part number. Part Select's picture showed the number, so I knew it was the right part.

Important to unplug the appliance first. There were two screws which were at the top opening of the oven. They were a bit obscure, but with a bit a searching, I was able to find them. After removing those two screws, the entire top lifted up. There were four screws from the bottom of that assembly which were easy to find, and once removed, the top lifted of easily. I found it easier to remove the two power lines with two easy disconnects, this made it easier to work on the assembly. The element itself was held down by two simple clamps which required no tools. There were four easy to remove wires, and the element came right off. Simply reversing the process put it right back together, plug it in, and back to cooking again.

Simply replaced old switch with new one. Was very easy to do.