G100 Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Nancy from Lakeville, MA
- Parts Used:
- 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The heat would not stay on keep heating up and turning off with no low heat
Unfortunately it was the wrong part I replaced the infinite switch and had the same problem so I am still trouble shooting but I plan to continue to use parts select they are excellent to work with and very quick to deliver parts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Temple Terrace, FL
- Parts Used:
- 700819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Heat Errosion
Wife installed them, they just snap into place on the Rock Grate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from Ocala, FL
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Holes in the air filter of our Jenn-Air grill
Simply pulled the old filter out and put the new filter in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from Santa Claus, IN
- Parts Used:
- 700855K
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Surface burner did not heat
I ordered part one day, recieved part the next day. I installed it the next day. It worked perfect. THANK YOU!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Camille from Marietta, GA
- Parts Used:
- 700855K
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Front burner elements had no temp control & only heated on full blast
I used process of elimination to figure out the issue with my 28 year old Jenn-Air cooktop. Issue: One day while cooking there was a loud pop & from then the front burner no longer had any temp control & only heated to full blast plus. Steps to fix: 1) Replaced the surface burner elements PS2195246 - this didn't fix the issue but they look nicer now. This was a simple plug in - no tools needed. 2) Replaced the grill side with a 2 burner plug in part PS1941381. Also simple plug in with no tools required. This didn't fix the isssue & I found that the front burner on the new unit also had no temp control. 3) Replaced the Surface Burner Receptacles for the 2 original burners PS1570190. This required turning off the breaker, removing the cooktop by unscrewing all the little screws & then cutting the old connections with wire cutters and wiring the new parts in with wire nuts & electrical tape. It took maybe half an hour but did not fix the issue. 4) Replaced the Surface Unit Infinite Switch Kit PS2076107 for the front 2 burners. Removed the screws just for the center control panel (after turning off the breaker) then took a picture of the wire configuration & removed the old parts by pulling (hard) at the connections until they unplugged. Put the new part in with the same wire placement. This finally fixed the issue & we now have 4 working burners for the first time in the >1 year that we have lived in this house.
Was this instruction helpful to you?
Thank you for voting!
stem on burner controls broken
follow the EASY to read and understand instructions.replaced all 4 controls in about 35 min.
Was this instruction helpful to you?
Thank you for voting!
bearing went out in blower motor
removed old motor from cooktop & motor housing & replaced w/ new motor & parts to install same. parts needed where screws & isolators (3).All went ok
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn W. from Lake Charles, LA
- Parts Used:
- 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The metal parts of the switches that the control knobs fit on broke on three of the switches.
I removed the two screws holding the control panel in place with a Phillips screwdriver, pulled the assembly of switches up, and found the number on the old switches. Amazingly on PartsSelect's website I found a picture of the exact switch with the exact same part number stamped on it. I ordered three new switches, and they arrived two or three days later. I removed the wires from the old switch with a pair of needle-nose pliers, reconnected them to the new switch in the exact same places, and had all three of them installed and working perfectly in about 45 minutes or an hour.
Was this instruction helpful to you?
Thank you for voting!
Both burners would come on when you turn on the back larg back burner.
Replaced surface unit infinite switch
Was this instruction helpful to you?
Thank you for voting!
bad infinite burner switch
unscrew control panel, remove old sw and put in new one. made sure i no mix up the wires. put in grease filter with old grease filter. I did not install the indicator light. More like a 30 yr old electric stove. model numbers are not even registering now. Maytag has parts for it. Have to look around to match up parts. Parts are common so inside the cartridges can be rebuilt with a set of plugs burners and receptacles that match.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barb from Holladay, UT
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replacement
This down draft filter was just what I was looking for. The big box stores (Home Depot and Lowe's) do not carry this size filter. Thanks,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Candace from Iowa Falls, IA
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed to replace the burner knobs on my stove.
Great company....Fast delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria from Nashua, NH
- Parts Used:
- 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
Burners Didn't Work
After a long time being without a working stovetop-an electrician friend said we needed to change a switch-it was ordered and came very quickly and installed-then it was determined that we needed a switch for the other side of the stovetop-I ordered it and got it the next day! It was a joy cooking thanksgiving dinner on a stove that worked-and I have a new friend that is interested in seeing me on a more regular basis. I know if I needed any kind of parts, I would check with partselect first ;)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Cottage Grove, OR
- Parts Used:
- 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Switch post broke. Could no longer turn that burner on.
Replacing the switch was quick and easy. It actually took only about two minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Kenai, AK
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The original filter was decomposing each time I washed it
I removed the protective grid over the filter and fan, turned the clip that held the filter in place and removed it. I placed the new intact filter for my antiquated Jenn-aire in its place, replaced the protective grid, and am happily continuing to cook on my functional cook top.Thank you.
Was this instruction helpful to you?
Thank you for voting!