2380EGS Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Portsmouth, NH
- Parts Used:
- WPY707453, WPY04100166, 715878
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Adaptor ring and drip bowl corroded over the years and the heating element was acting up.
I removed the old heating element, then the drip pan and then the adaptor ring. I cleaned the residue and buildup that was under the ring and on the surface below, I then snapped in to place the adaptor ring and then oriented and placed the drip bowl in place and finally oriented and pushed the heater element leads into their socket.
I turned the heating dial on and immediately felt the element warming up.
Checked Low temp and then Hi temp.
Everything is working and looking fine. The wife wants to replace the other ones, she says that it's easier than cleaning them.
I turned the heating dial on and immediately felt the element warming up.
Checked Low temp and then Hi temp.
Everything is working and looking fine. The wife wants to replace the other ones, she says that it's easier than cleaning them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sabra from Dallas, TX
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lost one of the knobs
Ordering and installing was easy. The hardest part was getting the exact match to 20 yr. old appliance knobs. First one I ordered had wrong shaft hole, but it matched perfectly in design. Decided to reorder and just replace all four with matching new-style knobs and the correct shaft hole. Yeah. Looks great and REALLY easy to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Brooksville, FL
- Parts Used:
- WPY707453
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ring adapter was the original and was pretty well worn through.
Removed the old adapter and replaced it with the bright and shiny new one that fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LouAnn from Maquoketa, IA
- Parts Used:
- WPY04100166
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
8 inch element not heating in cooktop
I removed the old element. I then plugged the new element in place. Simple repair, no tools required. Turned the cooktop element on to test for proper functioning. It heated properly. Repair completed.
Ordering the part was easy and it arrived within 2 days. Very happy with Parts Select service.
Ordering the part was easy and it arrived within 2 days. Very happy with Parts Select service.
Was this instruction helpful to you?
Thank you for voting!
Drip pans were in need of replacement
No brain surgery required. Removed electric burner, put in new drip pans. Voila! Good for many more years of service looking like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert A from Farmington `, CT
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old Stove Top
Ordered new cartridges
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martyn from Middletown, OH
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The original grease filter was damaged in our dishwasher (it is quite fragile) and needed to be replaced.
1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Alexandria, VA
- Parts Used:
- WPY04100166
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The radiant ring element had broken
Removed old element, plugged in new one, tested ok
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marjorie from Indianapolis, IN
- Parts Used:
- WPY04100165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
stove top burner would not heat
new element plugged into burner connection- an easy fix
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from Oceanside, CA
- Parts Used:
- WPY04100166
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My electric range burner was not heating.
All I had to do was remove the old burner and push the new burner into place. It couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from CONCORD, NC
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Burner plugs were loose
used the supplied parts...very easy. The parts were exact replacements.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lenice from Stuart, FL
- Parts Used:
- WPY700854
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Elec. stove-top knobs (imprinted with HI to LO numbers 1 to 10)worn to non-readable.
Knobs sent fit the shafts, but due to molded internal stop wouldn't seat. Had to drill out the stop, and also file down the shafts a bit for knobs to seat acceptably closer to stove-top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- alphonso from plainfield, IL
- Parts Used:
- WP71003558
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
blower motor was making loud noise
removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.
Was this instruction helpful to you?
Thank you for voting!