Models > CVE4180W-C > Instructions

CVE4180W-C Jenn-Air Cooktop - Instructions

Jump to:

All Instructions for the CVE4180W-C
76 - 90 of 170
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
JOANNE from MONKEY ISLAND, OK
Parts Used:
715878, 715877
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Drip pans were in need of replacement
No brain surgery required. Removed electric burner, put in new drip pans. Voila! Good for many more years of service looking like new.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Martin from Alexandria, VA
Parts Used:
WPY04100166
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The radiant ring element had broken
Removed old element, plugged in new one, tested ok
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Marjorie from Indianapolis, IN
Parts Used:
WPY04100165
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
stove top burner would not heat
new element plugged into burner connection- an easy fix
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joyce from Oceanside, CA
Parts Used:
WPY04100166
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
My electric range burner was not heating.
All I had to do was remove the old burner and push the new burner into place. It couldn't have been easier.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Natalie from North Reading, MA
Parts Used:
W11120791
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Wrench (Adjustable)
front burner stayed on high
We unplugged the range from the wall first so as not to get electrocuted. We removed the face of the control panel by removing the screws and 2 hex nuts underneath that hold it in place, and removed the trim. Then we disconnected the malfunctioning control switch, taking note of what order the wires go in. Hooked the new switch up and popped it through the face of the control panel. We then put the trim back, and reattached the control panel with the screws. Very easy!!
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Pittsburgh, PA
Parts Used:
WPY04100165
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
element shorted out
Replaced the element. The part came the next day which was great. Good customer service!
2 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Melissa from Buford, GA
Parts Used:
W10341820
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Fan Switch Broken and being held only by Electrical Wire Connections
removed two screws under fan cover at end of stove knobs. raised panel with knobs up and removed two nuts that held fan switch housing. installed new switch and moved power connections to new fan. (note: Killed power to range top prior to any repair action)
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Anthony from PORTLAND, OR
Parts Used:
W10341820, W11120791
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
large burner on cooktop would only operate on high no matter what setting it was at, fan switch did not function
First I located the proper breaker in my electrical panel to turn off the power to the cook top. Then I removed the two screws that hold the housing of the burner knobs and fan switch and lifted it up as much as the attached wires would allow me. To replace the Infinity Control Switch I removed the two "star" head screws from top of housing (under knob) which allowed me to pull the switch off of housing. I pulled off each wire, one at a time, and attached them to the identical place on the new control switch. With all the wires reattached I installed new switch into hole and replaced the 2 screws. To replace the fan switch I removed the 2 nuts on back of housing which allowed me to drop down the switch, swap the wires onto the new switch and place it back onto the bolt posts and reattach the nuts. Finally I turned the breaker back on and tested both new parts to make sure the problems had been corrected. Cook top works perfectly now.
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
richard from harlingen, TX
Parts Used:
W11120791
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
no heat to burner
Removed top and front panel
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tim from Lorton, VA
Parts Used:
W11120791
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
RF burner would not heat
1. Flipped breaker and confirmed no power at cooktop.
2. Removed the Fan grille and removed the two screws holding on the control panel. It tilts up and out to the rear.
3. Unscrewed the 2 screws on top holding old switch to panel.
4. Disconnected the wiring one lead at a time and connected it to the new switch in the same spot. There are 5 wires total and I carefully used needle nose pliers to remove reluctant wires and to adjust connectors if they were loose on new switch
5. Screwed the new switch onto the panel and screwed the panel back onto the cooktop.
6. Tested new switch...worked great.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
S.. J. from Punta Gorda, FL
Parts Used:
W11120791
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Electric barbecue element not heating
1. Diagnosed problem = switch at fault not element
Made a diagram of wire positions on faulty switch
2. Ordered part = remarkable service! Switch arrived in less than 24 hours
3.Installed new switch
4. Tested appliance = success!
5. Saved $150 and a lot of aggravation
Terrific site. Excellent help in figuring out and solving the problem. Two thumbs up!
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lawrence from Birmingham, AL
Parts Used:
W11120791
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
bad surface burner switch
1. Turn off power at breaker. Take no chances. Turn on each working burner, fan, oven light to be sure there is no power to the appliance. Then, turn them off.
2. Pull knob on switch straight out to remove.
3. Remove 4 Phillips head screws under control panel. Pull panel gently down, then out toward you slightly to release top edge. Rest control panel on self-clean lock knob.
4. Confirm terminals on new switch match up with old switch.
5. Use needle-nose pliers to gently remove wires from old switch one at a time and place them on the
corresponding terminal on new the switch.
6. Reverse steps 3, 2 and 1. Test switch and burner.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from Valley Grande, AL
Parts Used:
W11120791
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
back burn would turn high no mater where you set the control knob.
Well I was just guessing the controll switch was bad so I ordered a new one. So I cut off the power and held the switch close to the old one and changed the wires one at a time matching the connection terminals and cut the power back on and presto it WORKED..The service man wanted to charge me 65.00 dollars just to check it out. I figure I saved about 100.00 dollers plus I learned something.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Amy from Rosebush, MI
Parts Used:
W11120791
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
one of the four burners was not working
Very simple---shut off the power, removed six screws, detached five wires, replaced control switch, put everything back together, turned on power and made husband happy!!!
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Darrell from Moultrie, GA
Parts Used:
W10341820
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
switch too big for hole
switches had same parts numbers but were not the same size. Had to use die grinder and file to enlargh hole. took about 30 min.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the CVE4180W-C
76 - 90 of 170