2360 Hoover Cooktop - Instructions

Got a no-name tailor-it-yourself replacement switch from a San Jose, CA appliance parts store; but the switch was so cheaply made that it fell apart when I tested it.

Got a RobertShaw part from PartSelect and now the burner works perfectly.

The Model number could no longer be read clearly on the stove electric grill with a down draft vent system, so all I had was the size and looks of the old grease/air filter. I was very happy to come across Parts Select by way of an amazon.com search. Their web site's design and the parts pictures with detailed descriptions made it easy to find exactly what I needed. The grease filter fit perfectly in no time. I have successfully used my cooking grill again.

I TURNED OFF THE POWER TO THE GRILL FIRST. Then Removed the knob on the top face plate and then removed the 2 self tapping screws at the high end and this allowed the face plate to be pushed forward. And allowed access to remove the switch I removed the wires one at a time and replaced them on the new switch. All done in 20 minutes.

Turned off power at breaker. Removed screws holding control knobs in position. Removed knob and unscrewed nut holding switch in place. Noted wire positions and undid connections. Connected wires to new unit. Replaced nut and screws and control knob. Restored power and checked operation. You can do this. Don't call an electrician.

The 15-year-old Jen-Air stove started smelling really bad. I thought it was a dead animal stuck in the exhaust tube which runs under the floor to the outside. I flushed it out with clorine bleach, but it was still bad. It turned out to the be the grease filter. I washed it every week in the diswasher, but it just was not enough to get it clean enough. Finally, the grease went rancid and smelled really bad. This "repair" took about 30 seconds.

:-) - Just removed the old one and replace with the new one. Nothing to it. Takes 30 seconds.

It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.

Turned off breaker for range. Removed 4 phillips screws on control panel, tipped it forward and rested it on top of partially open oven door. Removed knob and nut on old switch. Moved wires, one at a time from old to new switch. Put new switch in place, tightened nut and pushed on knob. Put control panel back in place and installed 4 screws... piece of cake.

Replaced wires from broken to new part.

removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.

1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover

Turn off elec. power at breaker box. Check twice. Removed burner switch cover. caarefull remove wires from switch, note with color to which terminal remove nut on switch replace new switch replace wires to switch, replace cover turn on power. ready.

Removed 2 screws and i nut. Unplug the old switch and plug in the new switch and presto, back in business. Extremely easy. Part was exactly as pictured. Part arrived within 2 days. Great Co. to buy parts from. Highly recommend Partsselect.

Kill power to range unit at the breaker. Remove 2 screws on back of center control panel. Lift control panel up and toward rear of unit. Unscrew retainer nut which holds switch in the control panel. Carefully note wiring connections, and unplug all 5 wires from switch with pliers. Remove old switch. Reconnect all wires to new switch. Reattach switch to panel with retainer nut. Replace control panel in range with screws. Turn on power.

I first replaced the element and the receiver. This required splicing lines which was very easy. It still did not heat (even though my element indicator light was on) so I replaced the switch regulator. This took a little time because of the small space on my model. In fact, I had to replace a wire that had shorted by splicing a 3 inch section into it. When that was done, I simply re-connected the 5 wires in the original positions and reattached the cover. It works like a charm and my wife is delighted because we are hosting a family reunion/baby shower tomorrow!