JGP630SEK2SS General Electric Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Solomon A from COLLEGE PARK, GA
- Parts Used:
- WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The eye would not light
Remove the existing burner and install the replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from EL DORADO HLS, CA
- Parts Used:
- WB18T10338
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
One control knob igniter switch not working.
First take picture of cooktop. Go below cooktop and unplug electrical and turn off gas valve. Set burner greats aside along with bummer caps. Pull control knobs straight up and off, and set aside. Use 15 torque driver and remove two torque screws from each burner bases. Pull each white igniter up while holding the burner base in place. There is a wire attached to each igniter, separate the wire from the igniter and set aside. Once all igniters are removed, carefully remove all burner bases and set aside. Now lift top cover off. As you’re lifting the cover careful of the igniter wires. Now take another picture to refer to when installing new igniter harness. Notice where the harness plugs in and use pliers to remove the two plug connections from the igniter module. Then remove the rest of the harness from the top of the gas valves. Vacuum debris and clean up tray. Your last photo will be handy, refer to when installing igniter harness. Orient. All burner igniter switches the same on each gas valve. Check for wire clearance on wire harness. Reinstall top, guide igniter wires up through top, relocate burner bases in correct locations. Start all torque screws, leave loose until all igniters are reconnected and placed back down in there holes. Then tighten all torque screws. Reinstall burner caps, control knobs, and greats.
Go underneath and plug in power cord and turn gas valve on. Check all burners for correct operation.
Go underneath and plug in power cord and turn gas valve on. Check all burners for correct operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry L from Puyallup, WA
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rubber Grate foot worn or missing.
Replaced worn or missing Grate Foot with new ones. Took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Stratham, NH
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
feet keep falling off
Inserted the grate foot into the spot provided; after consulting the parts manuel to insure I was using the proper procedure.
I do use silicone to help hold the foot but it still won't hold
I do use silicone to help hold the foot but it still won't hold
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martha from DOWNERS GROVE, IL
- Parts Used:
- WB03T10217
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Knobs had melted
Pulled out the old. put the new ones on. Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from HENDERSONVLLE, NC
- Parts Used:
- WB02T10461
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rubber grate foot failed
Cut off approx. 1/8" in length for correct fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mohammad from BARTLETT, IL
- Parts Used:
- WB16K10055, WB16T10046
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The old burners were damaged by the prior owners.
The repair was extremely easy. Just removed the old burners and dropped in the new ones. No tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from SOUTH ELGIN, IL
- Parts Used:
- WB16T10046, WB16K10055
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burners wouldn't light
Had two burners on the stove that would not light. Had tried cleaning them but they still did not ignite. Replaced both burner heads. Once replaced. they ignited right away and have worked ever since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from ST AUGUSTINE, FL
- Parts Used:
- WB29K10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner cap replacement
I got really great customer service on finally getting the right part. It came really fast it fit perfect but the cap is a high gloss black instead of a flat black. I will need to call customer service again to see if they can the correct color this time.
Otherwise everything was great!
Otherwise everything was great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from HAMILTON, VA
- Parts Used:
- WB18T10338
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Gas Cooktop would not stop sparking - also one burner would not ignite electrically.
Shut off the gas and electric. Remove all the burner grates, burner caps, and burner valve knobs. Unscrew the two star screws holding down each burner base (an electric driver makes this quick and easy, but final tightening should be done by hand on reassembly). Carefully pry with a flat screwdriver each burner base assembly off the maintop assembly, being careful not to damage the spark igniters or burner gaskets. Carefully remove the electrical leads from each spark igniter, using pliers if necessary, and place the burner bases aside. Once all the burner bases have been removed, the maintop assembly can be raised off of the bottom burn box and set aside. Remove the top sheet of foil backed insulation foam from the burn box. Remove the old switch and harness assembly and disconnect black and white electrical leads. Using the diagram provided in the replacement part bag, install the new switch and harness assembly (it is not the same as the one being replaced, so you will need to follow the instructions). Reverse the above steps to re-assemble.
Overall this was a very quick and easy fix for the problem of constant sparking, it took about 30 minutes, and now my cooktop works like new, saving lots of $$$$ avoiding a replacement.
Overall this was a very quick and easy fix for the problem of constant sparking, it took about 30 minutes, and now my cooktop works like new, saving lots of $$$$ avoiding a replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from PASADENA, TX
- Parts Used:
- WB29K10023
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Food ran over the burner and damaged it.It was easy to place it back inII
It only required placing the new burner in the proper location.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from LEEDS, AL
- Parts Used:
- WB01K10112
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers
some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced
the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Broadalbin, NY
- Parts Used:
- WB02T10461
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
The Grate foot is to big for the hole.
I had to drill the hole to a larger size to enable the foot to fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GLENN from ST CLR SHORES, MI
- Parts Used:
- WB29K10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner cap wasn't working proper.
took burner off installed new one thank you for fast shipping
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juanita from GAINESVILLE, GA
- Parts Used:
- WB16K10070, WB16T10046, WB16K10055
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
gas burners not heating evenly
remove old burner, put new in place
Was this instruction helpful to you?
Thank you for voting!