JGP5536SL1SS General Electric Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gene from Simi Valley, CA
- Parts Used:
- WB02T10461
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Leaking from front door
First remove the screws around the inside perimeter of the door. These require a special hex driver. Take off the inside plastic liner of door.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The Insulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The Insulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- judith from boardman, OH
- Parts Used:
- WB16T10037
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
warped burner
reinstalled new one. just a little better than than the warped one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara J from Sweetwater, TX
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Missing grate foot.
Ordered by phone parts & very pleased with all of transaction.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tom from san pedro, CA
- Parts Used:
- WB04T10014, WB04T10012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
burner flame out of control
Replaced burner gaskets.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Watertown, MA
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the grate foots came off
put it in but it keeps falling out. they're made narrower than my oven grate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Bakersfield, CA
- Parts Used:
- WB02T10461, WB13X27058, WB04T10011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
gas igniter not working
Remove burner, replaced gasket and spark igniter. On bottom of grill replaced missing rubber foot protectors. Initially I thought I would have to splice into the igniter wire however, after watching the video on repair, I discover all I had to do was carefully pull the wire out of the igniter from the bottom and push the wire into the bottom of the new igniter, then replace the burner into position and tighten the trox screws. It was a simple repair and everything is working fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Port Orchard, WA
- Parts Used:
- WB16T10035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burners are supposed to burn with a blue flame. Two burners had yellow flames
New burner Heads repaired the two yellow burning units. I believe heat caused the old heads to become. warped over time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Kenner, LA
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grate Foot Have 8 For My Stove And One Breaks Every Now And Then
This was and always will be an easy fix, all I have to do is get my ice pick and pick the broken rubber part stuck in the hole if it does not break clean and fall out. Not much more I can say about this simple problem.
Was this instruction helpful to you?
Thank you for voting!