PP989DN5BB General Electric Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Andrea from ORLANDO, FL
- Parts Used:
- WB30T10133
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
9" Radiant Element did not heat up.
I started by Unscrewing the range top. 2 small screws. I took off the old piece by unclipping the piece . Then I color coded each wire so that I would know exactly where I would place the wires for the new part. 30 min maximum time spent changing the part. Please don't forget to unplug the range before you start.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from ST CLR SHORES, MI
- Parts Used:
- WB30T10133
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Original heating Element was burned out
1st replacement part was damaged from Shipping.
Parts Select sent a new one that i received in only a few days.
our stove is slid into a granite island so the disassembly was not as simple as most. It was necessary to remove the controls, the controls housing & screws along the top of the oven door.
Within an hour the stove was back in place and working perfectly.
Great service from Parts Select
Parts Select sent a new one that i received in only a few days.
our stove is slid into a granite island so the disassembly was not as simple as most. It was necessary to remove the controls, the controls housing & screws along the top of the oven door.
Within an hour the stove was back in place and working perfectly.
Great service from Parts Select
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from JOHNSONVILLE, SC
- Parts Used:
- WB30T10133
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Element bad
Since this was the third time I did it all I had to take two screws out to lift the top of stove and replace element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Prem from WOODBURY, CT
- Parts Used:
- WB24X10174
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
Broken shaft on downdraft speed switch
The controls are on the glasstop and no way to access them from below, so the glass top has to be removed by removing any straps/braces from below and raising the rangetop housing above the counter height.
The foil tape connecting to the downdraft ductwork will need to be removed. Make sure you have foil tape to reseal this connection.
The black foam tape between the cooktop housing and the countertop will need to be separated with a putty knife. Be sure to have the 1/4” low density foam tape on hand for replacement.
Remove the 6 knobs by lifting them upward and then lift the housing above counter height.
The loosened housing can be supported by two pieces of 1x2 that straddle the opening. The sheet metal screws around the perimeter are easily removed and a putty knife under the glass should release the glass. Once the glass is removed, you’ll see an electrical control box with the 6 switches. The fan switch is held in place with two screws. The switch can then be accessed from the side and replaced. Just note the 4 colored wires and move them to the new switch. There’s a 5th contact that’s unused.
Reassembly is straightforward but you’ll need to remove any remaining foam tape, clean the underside and the countertop before applying the new tape.
The foil tape connecting to the downdraft ductwork will need to be removed. Make sure you have foil tape to reseal this connection.
The black foam tape between the cooktop housing and the countertop will need to be separated with a putty knife. Be sure to have the 1/4” low density foam tape on hand for replacement.
Remove the 6 knobs by lifting them upward and then lift the housing above counter height.
The loosened housing can be supported by two pieces of 1x2 that straddle the opening. The sheet metal screws around the perimeter are easily removed and a putty knife under the glass should release the glass. Once the glass is removed, you’ll see an electrical control box with the 6 switches. The fan switch is held in place with two screws. The switch can then be accessed from the side and replaced. Just note the 4 colored wires and move them to the new switch. There’s a 5th contact that’s unused.
Reassembly is straightforward but you’ll need to remove any remaining foam tape, clean the underside and the countertop before applying the new tape.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from CLEMMONS, NC
- Parts Used:
- WB30T10133
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Small radiant wasn't working but large was.
Ordered the dual replacement. I am 76 so I had someone else do it. It took him about 15 minutes. Just pulled the oven forward about 8" so he could lift the top up. 2 Screws to release the top. Then just removed the part and plugged in the replacement. Rescrewed the top screws and pushed the oven back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Philadelphia, PA
- Parts Used:
- WB30T10129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner not operational.
Disconnected power supply. Removed damaged element by releasing retainer clips and unplugging wire contacts. Replaced with new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from HIGHLANDS RANCH, CO
- Parts Used:
- WB30T10133
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
one burner not working
Removed two screws to access burner. Removed three power clips from burner, reattached the clips to new burner, removed brace clips and attach to new burner, close lid and reattach stove cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth Ann from New Columbia, PA
- Parts Used:
- WB30T10133
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The middle of the element quit working.
Took the old burner out, tranferred the wires from old to new. Installed the new burner. Works fine.
Was this instruction helpful to you?
Thank you for voting!