Models > JGP330SEK2SS > Instructions

JGP330SEK2SS General Electric Cooktop - Instructions

Jump to:

All Instructions for the JGP330SEK2SS

Customer:: Douglas from Knoxville, TN
Parts Used:: WB13X46909
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

The spark module would constantly spark

I ordered the spark module and replaced it which was veru simple, plugged it in and it sparked only now and again. I finally said forget it and it has now stopped sparking but for how long I do not know.

Was this instruction helpful to you?

Customer:: Joan from Warren, NJ
Parts Used:: WB02T10461, WB29K10023
Difficulty Level:: A Bit Difficult
Total Repair Time:: 15 - 30 mins

Both items needed to replace broken or non existent ones

The burner cap was a no brainer. The grate feet should have been also, but many of them were undersized so we had to maneuver them in such a way that they didn't fall out of the grates.

Was this instruction helpful to you?

Customer:: Charles from Houston, TX
Parts Used:: WB16K10055
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Replace medium burner for gas cooktop

Very easy to remove grates, burner cover and remove old burner head. Very simple process, but surprised that there was no efficient way to clean carbon deposits from my old burner. Burner video instructions on line insured I installed the new burner head correctly (actually, pretty hard to get wrong), and burner worked correctly immediately. Will likely replace other burners in time as the new one is so "silvery" colored compared to my other burners.

Was this instruction helpful to you?

Customer:: Jerry from Danville, IL
Parts Used:: WB18T10339
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

igniter kept igniting

Simply removed the 9 T9 screws from the top of the cooktop, removed the igniter spark modules, lifted the top of the cooktop up and removed harness assembly. Unplug harness from spark module and replaced in same fashion. SUPER EASY done in less than 15 minutes

Was this instruction helpful to you?

Customer:: Vincent from Leesburg, VA
Parts Used:: WB18T10339
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

One Burner would not light when using the corresponding knob..

Good way to tell/verify what your problem is. On my GE Cooktop, moving any of the knobs to light cause a spark for all igniters. One of our knobs would not cause a spark. - Remove gas grills and covers. - Remove screws - Pull igniters up (be gentle to not crack them - Pull wire out from igniter - lift cover of cooktop - pull harness off each know and disconnect two wires - put new harness on and connect and backfill. Pretty easy overall.

Was this instruction helpful to you?

Customer:: Jesse from Nashville, TN
Parts Used:: WB13K10014
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins

Large burner wasn't lighting very quickly

Removed grill grates, gas distributors, etc. (just lift off). Used star screwdriver to remove screws (3 per burner for SML, 2 for power burner). Lift off stainless cover, which also lifts off the white sparkers I was replacing. Pull them off the wires (didn't need pliers, others said they did). Replace (make sure it is all the way on) and reverse your steps. White sparkers electrodes seemed loose when I put them back on, but tightened up when I fully secured the top back on. Make sure the wires aren't pinched underneath when you put the top back on. Recommended: If you've got one that isn't working, go ahead and replace all 3 (power burner is different) because the part is so cheap you may as well just do it now.

Was this instruction helpful to you?

Customer:: Lee from Kenner, LA
Parts Used:: WB02T10461
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Grate Foot Have 8 For My Stove And One Breaks Every Now And Then

This was and always will be an easy fix, all I have to do is get my ice pick and pick the broken rubber part stuck in the hole if it does not break clean and fall out. Not much more I can say about this simple problem.

Was this instruction helpful to you?

Customer:: Sandra from Watertown, MA
Parts Used:: WB02T10461
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

the grate foots came off

put it in but it keeps falling out. they're made narrower than my oven grate.

Was this instruction helpful to you?

Customer:: Arthur from Riverside, RI
Parts Used:: WB16T10046
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Hot Spot On Burner

Replaced old burner element with new, easy

Was this instruction helpful to you?

Customer:: glen from felch, MI
Parts Used:: WB16T10046
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

uneven flame and sputtered, burner was not useable

Simple to correct 1. lift off grate 2. lift off burner cover 3. lift off old burner. 4. replace burner, cover and grate. took 10 seconds. burner works perfect

Was this instruction helpful to you?

Customer:: Francisco from Cypress, TX
Parts Used:: WB03T10217
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Accidentally burned two original knobs

Could not get the model number of the cooktop stove. GE hides it very well. But, I found a replacement knob on your web that looked similar to my original. The photo of the replacement was very accurate in terms of showing its true size and configuration of the stem. This photo showed that the prospective replacement would match the original´s configuration and it did. Plus, it was the most inexpensive knob among the ones available in this or other sites. Great site.

Was this instruction helpful to you?

Customer:: Stephen from North Las Vegas, NV
Parts Used:: WB16K10070, WB16K10055, WB16T10046
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

carbonized burners

Replaced all four

Was this instruction helpful to you?

All Instructions for the JGP330SEK2SS