JP651*J1 General Electric Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Debby from Wimberley, TX
- Parts Used:
- WB30X348
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Burner supports broke, no longer could use the burner
Cut the power off to the range, unscrewed the burner from range and pulled off the element and unscrewed the two screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bradley from Gate City, VA
- Parts Used:
- WB32X10013, WB32X10012, WB31X5014, WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old and rusted rings and pans
lift stove eyes and replace
Was this instruction helpful to you?
Thank you for voting!
Old trim rings were rusted and soiled
Too easy to describe. Just lifted out the old rings and popped in the new ones. PartSelect is my go-to source for appliance parts both for my home and my job as maintenance man for residential group homes in my area. Website is easy to use, prices are good, shipping is always surprisingly fast. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from Harvard, MA
- Parts Used:
- WB21X36771
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The control knob stem broke off when I moved the stove.
I located and removed 2 sets of hex-head screws under the front lip of the cooktop, then lifted the entire cooktop to access the burner controls. Removed the wires and taped them, and took out the old control after removing 2 phillips head screws. Installed replacement part easily. Only tricky part is that the various shaft adapters don't quite work with my knob. I'll fix it completely with a bit of epoxy and the adapters they sent.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from High Bridge, NJ
- Parts Used:
- WB30X348
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element ruptured and wouldn't heat
The replacement was easy: turned off breaker to range; unscrewed element from range top;opened ceramic terminal box; unscrewed element from range wires. Then I simply reversed the procedure, using the new parts. Easy to do and it only took about 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Woodlawn, KY
- Parts Used:
- WB30X348
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner would not heat
i removed the two screws that hold the element in place. i then pulled the element out and disconnected the two wires. then i connected the two wires and screwed the element back in place and now it works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Houston, TX
- Parts Used:
- WB30X348
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Broken Wire
A simple repair using your quality matched Part turned into a CONDOMINIUM CIRCUS (no fault due to the Part or PartSelect.Com.)
It was the 1st time in over 30 yrs. that we had to throw a Circuit Breaker Switch located outside in the communal large Metal Box between Condos. Not only did it NOT cut the power off our old GE Range - it turned off one neighbor's T.V. & another neighbor's Washer/Dryer Set.
As more Breakers were tried - MORE ANGRY NEIGHBORS ARRIVED ON THE PATIO. To complicate this - the next-door Condo just underwent extensive (read 3 Months) Renovation including REPLACING ALL WIRING..... and you might imagine the rest. No Breaker Switch numbers matched the Condo number written beside them in felt tip pen... it was complete chaos!
THANKS to PartSelect.Com our old G.E. is working again.
Yours truly,
William Rush,
It was the 1st time in over 30 yrs. that we had to throw a Circuit Breaker Switch located outside in the communal large Metal Box between Condos. Not only did it NOT cut the power off our old GE Range - it turned off one neighbor's T.V. & another neighbor's Washer/Dryer Set.
As more Breakers were tried - MORE ANGRY NEIGHBORS ARRIVED ON THE PATIO. To complicate this - the next-door Condo just underwent extensive (read 3 Months) Renovation including REPLACING ALL WIRING..... and you might imagine the rest. No Breaker Switch numbers matched the Condo number written beside them in felt tip pen... it was complete chaos!
THANKS to PartSelect.Com our old G.E. is working again.
Yours truly,
William Rush,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RONALD W from PISCATAWAY, NJ
- Parts Used:
- WB30X348
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Heating Element Burn Out
Easy to do . Four screws,removed cover,removed switch. Installed switch,and cover. Time 1/2 hr.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Preston from cincinnati, OH
- Parts Used:
- WB32X10013, WB32X10012, WB31X5014, WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
drip pan, trim ring were old and burned
just replaced the old for the new
Was this instruction helpful to you?
Thank you for voting!
I needed new trim rings around the stove burners
I logged into GE's website, put in my stovetop's requirements for size and type of trim rings, and was taken to partselect's site where I found what I needed. I ordered it and it came in less than a week!
Was this instruction helpful to you?
Thank you for voting!
original 8" coil burner defective
Took coil mounting assembly off first, then removed or took apart one piece at a time until heater coil was removed. Then installed (with furnished screws)the new coil, following entire process in reverse. 10-15 minutes time.
Was this instruction helpful to you?
Thank you for voting!
Element had burned out.
The repair was straight forward; Loosen the screw at the tilt mechanism allowing the burner element to come off the stove and then unscrew two electrical connectors freeing the burned element. The installation could have been as easy as reversing the procedure however the lugs on the new element were poorly placed making it difficult to attach the two halves of the supplied insulator with the clips that secure the two halves. The insulator required the wires to be bent 90 degrees which further complicated the installation. A dremel and some dielectric grease completed the task to my satisfaction. It should have been a 15 minute job. The new element functions far better that the burned element prior to its demise. I should have changed it long ago. I bought the 8" element as a back-up because this stove has only one large burner. However, given my experience with the improvement of the 6", I'll change it shortly. And knowing I may run into the same installation hiccup, I'll prefit the ceramic insulator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark A from Industry, PA
- Parts Used:
- WB32X10013, WB32X10012, WB30X359
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner element had burned out
turn off power at breaker. lift element from stove top lift out drip bowl . remove clips and ceramic cover. unfasten three wires. using new element install three wires to new burner ,clip on ceramic cover then slide burner back in to stove top and install drip bowl turn on power and test
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLARD from GLOVERSVILLE, NY
- Parts Used:
- WB21X36771
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
instructions could be better
it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from San Antonio, TX
- Parts Used:
- WB32X10013, WB32X10012
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Old drip pans rusted out.
Range is 45 yrs old. New drip pans are different shape. This is only place which had them and VERY GOOD price. Delivery was quick, too!
Was this instruction helpful to you?
Thank you for voting!