Models > JGP333DET1WW > Instructions

JGP333DET1WW General Electric Cooktop - Instructions

Jump to:

All Instructions for the JGP333DET1WW
16 - 30 of 52
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Anne from Plainview, NY
Parts Used:
WB29K10024, WB29K10022
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
burner caps began to chip
I removed the two range grills. Then I removed the two chipped burner caps, and replaced them with the new burner caps. I then replaced the two range grills.
5 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Astrid from MORAGA, CA
Parts Used:
WB16K10055, WB29K10023
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
THE OLD BURNER HEAD WAS NOT TURNING ON PROPERLY AND THE GAS CAME OUT UNEVEN.
I JUST EXCHANGED THE BURNER AND BURNER CAP.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Wesley from FRANKLIN, TN
Parts Used:
WB13K10014
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers
Gas range igniter was making a clicking sound every 3 to 5 minutes, as if it was trying to ignite one of the burners.
Unplug the range from its wall socket to avoid electric shock. The various range parts that support a pot or frypan are easily lifted off their perches, exposing the small white igniter. The only moderately difficult aspect is wiggling the igniter out of its retainer. The electric wire leading into it then can be pulled out and fed into the new igniter with a push. Replace igniter in its retainer, then replace the range parts you removed to expose the igniter and plug the range back into the wall socket. Piece of cake.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gary from Indio, CA
Parts Used:
WB29K10004
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
we had damaged the burner cap
just removed the old burner cap and put on the new one.
4 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Akshay from Bridgeton, NJ
Parts Used:
WB16T10046
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Burner had uneven flames
Too easy a five year old could do it
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Solomon A from COLLEGE PARK, GA
Parts Used:
WB16T10046
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
The eye would not light
Remove the existing burner and install the replacement.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Terry L from Puyallup, WA
Parts Used:
WB02T10461
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Rubber Grate foot worn or missing.
Replaced worn or missing Grate Foot with new ones. Took less than 5 minutes.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from Stratham, NH
Parts Used:
WB02T10461
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
feet keep falling off
Inserted the grate foot into the spot provided; after consulting the parts manuel to insure I was using the proper procedure.

I do use silicone to help hold the foot but it still won't hold
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
paul from las vegas, NV
Parts Used:
WB13T10046
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Sparking at 2 different burners all by themselves
Replaced Spark Module and adjusted igniters
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dana from LEEDS, AL
Parts Used:
WB01K10112
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours
Tools:
Pliers
some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced
the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rita from ST AUGUSTINE, FL
Parts Used:
WB29K10024
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Burner cap replacement
I got really great customer service on finally getting the right part. It came really fast it fit perfect but the cap is a high gloss black instead of a flat black. I will need to call customer service again to see if they can the correct color this time.
Otherwise everything was great!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Juanita from GAINESVILLE, GA
Parts Used:
WB16K10070, WB16T10046, WB16K10055
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
gas burners not heating evenly
remove old burner, put new in place
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sam from Austin, TX
Parts Used:
WB13X27058
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Replacing ignitor
Got ignitor and it did not have wire attached as shown in the picture of parts. However, all I did was take burner cap off, and gently life ignitor up and out, detach the wire, attach new ignitor to wire and reset.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gary from HENDERSONVLLE, NC
Parts Used:
WB02T10461
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Rubber grate foot failed
Cut off approx. 1/8" in length for correct fit.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
O.Robert from Montrose, PA
Parts Used:
WB13T10065
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
The electrode had broke
I unscrewed the base where the electrode was attached to detached the electrode detached the wire to the electrode inserted new electrode with holding spring and clamp attached wire to electrode.
I then put the base back on top and screwed in the two screws assembled the remaining parts and turned on the stove unit and it worked I am very happy.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JGP333DET1WW
16 - 30 of 52