JP6519C1 General Electric Cooktop - Instructions

The original controls were different for the small burners and the large burners. The replacement part fits all. Before removing wires, pay attention to writing on new and old control and replace 1 at a time. The hardest part was being sure to cut the knob stem to the correct length. Control works well.

Turned off the breaker to the range. Turned on range to ensure no electricity was currently flowing to the range. Turned the range off and unscrewed the tilt lock hinge. Pulled the burner out to expose the wires. Popped the snap locks off the cover box and unscrewed the wires connected to the posts. Followed recommend directions to expose approx. 1/2" of new wire (this is what I used the knife for since I did not have a wire stripper available). Slightly cut thumb in the process (no blood, though). Removed old burner. Put new burner in place, re-attached wires to the posts and screwed in to place. Placed cover box back in place and secured using new snap locks. Attached tilt lock hinge using new screw that was provided. Turned breaker back on and turned on range. new burner worked great. Took about 20 minutes total. Wife was extremely impressed, mostly that I didn't electrocute myself. She now wants me to replace other three burners. No good deed goes unpunished.

I read parts select instructions and i was done in less than 30 minutes. Since 1988, this is the 1st. part that I had to replace. I now have parts select on my favorites list.

Replaced 30 year old stovetop cooking element with no problems. Stovetop works great now.

slid the range away from wall. disconnect power. removed back,compared switches and marked wires.installed new switch and wires.the adapter for the control knob was a problem it left the knob out futher than original i had to modify the plastic adapter and got it close enought! the most time spent was cleaning up the floor before putting the range back.

Threw away the old ones after lifting burner rings. Put new parts in place.

I tried first to replace them, with a set I bought at a local hardware store. But they were too small. So I went on the internet, and found Part Select, and thanks to a very helpful guy, who made the extra effort to find the exact drip bowls, I now have a nice, shiny stove-top again. Installing them took two minutes... tilt the burners up, and slide them in. No problem.

My stove top is 35 yr old. & Lowes did not have drip pans that fit. these worked great & easier than cleaning the old ones. They just popped right in.

Simply removed old and inserted new. No tools necessary.

This is twin oven range with controls at side of upper oven. Control panel was fastened with screws at top and bottom. Range has built-in hood at top which had to be disassembled to reach top screw. Once had access to top screw, eaisly removed control panel and replaced control. New control had identical connections as old control so only had to install it, break shaft to correct length, and use proper shaft adapter for knob. Remounted control panel and range worked perfectly. This would have been a very quick job except for having to deal with the built-in range hood.

(Turn off the Power) Pull stove out, remove the 2 screws that holds switch in place, remove one wire at a time and install on new switch. Slip switch in replace 2 screws. Snap off about 3/4 of the shaft cut down plastic insert for knob, install knob turn on power and it works.

Replaced the old with the new following directions (mostly).

1. The infinite switch had several knobs which would fit the switch shaft. Read the directions included with the switch in order to have the shaft fit the proper knob. You can break the shaft with two pairs of pliers. 2. Move the stove away from the wall and unplug it. 3. Remove the 1/4 screws from the back side of the stove and remove the back panel, exposing the switch. 4. Remove the wires one at a time and put them on the new switch. The terminals are L1, L2, P, H1 & H2. The Pilot (p) has a smaller terminal so you don't get it mixed up. Generally L1 is black, L1 is red, P is yellow, H1 and H2 can be blue, brown, yellow, orange or one of these colors striped on a white wire. 5. Remove the old switch from the stove and be sure to save the two mounting screws. 6. Position the new switch so that the side of the switch marked "top" is on top. 7. Install the screws on the new switch and put the knob on it. 8. Carefully test the burner. 9. Unplug the stove and put the back cover on.