JGP330BEK2BB General Electric Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from ABINGDON, VA
- Parts Used:
- WB18T10339, WB13X46909
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Gas coke top wouldn't lite
First step is to turn off the electrical then disassemble the cook top. It is secured to pan by each of the burner mechanisms. Disconnect the spark wire from each porcelain drip pan. Separate the glass top from the pan. If it's stuck gently slide a putty knife int between the two to separate and carefully set the glass top aside. The spark module was a bit challenging in that the colors of the wires didn't match so if you aren't comfortable with electrical work I would get help. The module didn't fit the bracket so,I had to drill new holes and use self tapping screws to mount it. The other part part I intended to change was the spark igniter switch. Unfortunately the wiring was incompatible so I had to return that part. This top was sold by Kenmore but made by GE and is over 10 years old so I suspect an engineering change obsoleted my part. Overall the job wasn't that bad if you are reasonably mechanical..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from BEAVERCREEK, OH
- Parts Used:
- WB18T10339
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Igniter constantly ticking ...
Unplug!!
Pull knobs
Pull burner centers
Unscrew the nut at the center of each burner
Tilt cover up revealing under burner controls
Remove old harness
Install new harness
Reassemble in reverse order
Plug in NO ticking
Pull knobs
Pull burner centers
Unscrew the nut at the center of each burner
Tilt cover up revealing under burner controls
Remove old harness
Install new harness
Reassemble in reverse order
Plug in NO ticking
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Akshay from Bridgeton, NJ
- Parts Used:
- WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner had uneven flames
Too easy a five year old could do it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Solomon A from COLLEGE PARK, GA
- Parts Used:
- WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The eye would not light
Remove the existing burner and install the replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martha from DOWNERS GROVE, IL
- Parts Used:
- WB03T10217
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Knobs had melted
Pulled out the old. put the new ones on. Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry L from Puyallup, WA
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rubber Grate foot worn or missing.
Replaced worn or missing Grate Foot with new ones. Took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Stratham, NH
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
feet keep falling off
Inserted the grate foot into the spot provided; after consulting the parts manuel to insure I was using the proper procedure.
I do use silicone to help hold the foot but it still won't hold
I do use silicone to help hold the foot but it still won't hold
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from HENDERSONVLLE, NC
- Parts Used:
- WB02T10461
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rubber grate foot failed
Cut off approx. 1/8" in length for correct fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from UPLAND, CA
- Parts Used:
- WB18T10339, WB13X46909
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Igniters would not turn off
Replaced starter switch harness as well as igniter module. Cost was around $70 for parts. Cheaper than a new cooktop.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from las vegas, NV
- Parts Used:
- WB13X46909
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Sparking at 2 different burners all by themselves
Replaced Spark Module and adjusted igniters
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from HUMBLE, TX
- Parts Used:
- WB18T10339, WB13X46909, WB03T10217
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
IGNITER INOP
REMOVE GRILL AND TOP OF BURNERS. CLEAN GUNK OUT OF TORQUE SCREWS AND TRIED TO REMOVE TOP PLATE. FOUND IGNITERS ALSO NEED TO COME OUT, THEY HAD HEAVY DEPOSIT,
BE CAREFUL. ONCE I GOT THEM OUT, JOB WENT WELL. NOTE
MAKE SURE ALL CONNECTION ARE CLEANED BEFORE REASSEMBLY.
BE CAREFUL. ONCE I GOT THEM OUT, JOB WENT WELL. NOTE
MAKE SURE ALL CONNECTION ARE CLEANED BEFORE REASSEMBLY.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mohammad from BARTLETT, IL
- Parts Used:
- WB16K10055, WB16T10046
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The old burners were damaged by the prior owners.
The repair was extremely easy. Just removed the old burners and dropped in the new ones. No tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from SOUTH ELGIN, IL
- Parts Used:
- WB16T10046, WB16K10055
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burners wouldn't light
Had two burners on the stove that would not light. Had tried cleaning them but they still did not ignite. Replaced both burner heads. Once replaced. they ignited right away and have worked ever since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from LEEDS, AL
- Parts Used:
- WB01K10112
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers
some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced
the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Broadalbin, NY
- Parts Used:
- WB02T10461
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
The Grate foot is to big for the hole.
I had to drill the hole to a larger size to enable the foot to fit.
Was this instruction helpful to you?
Thank you for voting!