JP989CC1CC General Electric Cooktop - Instructions

Removed the two screws that hold the range top down. Lifted up yhe range top and propped with a stick. Proceeded to mark the wires connected to the old burner so that the new one would be connected correctly. Removed the wires and then the two brackets that hold the burner in place. Removed the old burner and installed the new one. Connected the wires and resecured top to base. Turned on the current and it worked beautifully.

I removed the screws from the underside of the stovetop, lifted up the top, propped it up to keep it from falling (using a large book), and removed the old burner by unscrewing it from the top and removing the wire connections. I then screwed the new burner into the top, and attached the wires back to the burner, dropped the top down (gently and carefully, of course), and screwed the top back down to the rest of the stove. It was fairly quick and painless. Although, putting the stove back into his position was not easy, but that was no fault of the stove!!

Very simple repair. Remove two screws to lift the range top. Then remove the two screws holding the element in place. Disconnect the wires from the old element, connect the wires to the new element. Reverse the procedure and you are done. Total time is anywhere from 15 to 30 minutes.

turn off breaker, two screws hold down cooktop, 8 screws take top off cooktop. unplug switch, install new switch. repair loose connections. put back together. pretty simple

after removing the two screws that are just inside the oven, I propted the top open with the box that the part came in. I drew and labeled the wires as I took them off using a color coding. next I removed the two clips that held the burner in place and marked on the new burner exactly where the clips were attached. Replacing the clips was possibly the hardest part of the whole operation. When you replace the burner, don't forget to replace the insulation pad that is stuck one the metal where the conections are. I missed this and had to reopen the stovetop and slid it on after I was finished. Otherwise it went pretty smooth.

Turn off power to cook top. Remove 2 screws that hold the cook top to countertop. Lift complete cook top from counter and place diagonally across opening. Remove 10 screws that hold glass top to the component cabinet. Make a diagram of wiring to element. Disconnect wires. Remove 2 mounting brackets from bottom of old element and position them on new element and screw tight. Wire new element as diagrammed earlier. Replace glass top on component cabinet and reinstall 10 screws. Place unit back into counter opening and secure with 2 straps. Turn power back on. Stand back and enjoy your accomplishment.

Robert did not do the repairs. I did! 70 year old housewife. I watched a Utube video and thought I could certainly handle that. Ordered my part from your site. It came in two days. Burnet was replaced in under 20 minutes by me! Anyone can do this. Super easy, parts just plug in.

Remove two screws hold cook top down: prop it open with piece of wood. (TURN OFF POWER TO RANGE FIRST!). Carefully make diagram of where wires go: remove and replace.. piece of cake!

Pull out Range and unplug from wall receptacle. Open Range door and remove 2 hex head screws with pliers. Screws located at top inside of range door opening. They hold the burner top in place. Slowly lift front of top burner section up and at same time slightly lifting back of burner section since it rests on 2 pivots. Prop front of burner section open, tilted back, with a piece of 2X4 maybe 2 1/2 ft. long. Make sure the 2X4 is located at the front/middle of range [resting on insulation] and at front middle of burner top to keep it opened firmly and balanced. You have about 5 or 6 wire clips to remove from elec. posts. Use pliers to gently remove clips. Tag the wires with tape to remember which wires go onto the new burner. Or take a close up picture with your phone to remember which wires go where. There are 2 philips head screws holding clips that hold the burner in place. The clips are slipped into a slot to help hold them in place. Mark the 2 slots so that when you remove the clips you will remember which slots to put them back into. You will need to hold the burner with one hand while you are removing the last clip as it could just fall out. Remove old burner and install new burner at same angle as was the old burner. You will have to make sure that the 2 clips are in the slotted openings first as you can not put them in place after the burner is installed in the opening. Reinstall the 2 screws into the 2 clips. Hold the electrical pole fittings with one hand while you gently reattach the electrical clips with a set of pliers. You may need to wiggle the clips back and forth to get them on securely. Remove the 2X4 and gently lower the burner top. The hardest part is now you have to slightly lift the back of the burner top while the front is lifted up and maneuver the back to drop down over the 2 pivots. Then the burner top will drop down in place so that the 2 screws in the range door opening can be reinstalled. I don't know of an easy way of making the top of the burner section fall down over the pivots except trial and error. Maybe use a flashlight to look back where the pivots are located while the top is propped open. That may help you visually to see what you are trying to do.

The cooktop is just set in the counter with no fasteners. I shut off the power and lifted the unit out. Ten small screws held the top to the body. After removal, I took a picture to have a wiring reference. I disconnected five wires with push-on terminals, then removed two Tinnerman nuts with needle-nose pliers. The failed burner was free to remove. There were two mounting ears on the bottom of the burner at positions 12 and 48 as stamped on the bottom. I transferred the mounting ears to the new burner, one screw each. I then positioned the new burner and secured with the two Tinnerman nuts, replaced the five wires, screwed the top back on and slipped the unit into the counter. Done.

Turned off power. Opened range door, removed 2 screws that held top in place. Took a photo of the existing wiring for reference. Removed old burner. Be careful with spacers & springs. If dropped, they will be hard to locate in the insulation. Replaced wiring connectors & verified proper location with photo. Closed cover, replaced 2 screws & turned on circuit breaker.

lift stove top, 2 undermount screws. Then unplug 4 wires, I did them 1 at a time plugging into new burner as I go so I wouldn't screw up. Take 2 screws out of old burner to stove top, # all around circle put screws in same # on new burner.Done Good experience all the way around. Order delivery and install

Remove two screws to loosen the ceramic top....prop top open and change part...the part was exactly the same...change wires from one to the other and transfer clamps.....1st grade craft class would have done it in half the time I did......you folks have your parts inventory and description application to a science.....God Bless

1.Move range in position to access electrical wall disconnect and unplug. 2.Remove two 5/16 screws (located under top fwd. edge of cook top, Lift entire top assy up from front and prop with appropriate device(short 2x4 about18 inches long works well) 3.Remove two small phillips screws securing two metallic keeper devices holding burner assy in place. This should allow burner assy to be removed.4.Disconnect electrical spade connectors from ceramic terminal blocks on old burner assy.CAUTION: [SPADE CONNECTORS FIT TIGHTLY DO NOT PULL ON WIRES USE PRYING FORCE WITH FLAT SCREWDRIVER DIRECTLY ON TERMINAL].Remove connectors one at a time re-connecting to same location on new assy. Reassemble in reverse order.

Very easy. Unpluged range from outlet, took two screws from the front under side of the range top, raised cook top up, took off four wires from burner, removed two screws than holds burner on cook top, replaced with new burner, installed two screws that hold burner in place, installed the four wires to burner, lowered cook top back into place replaced two screws that hold cook top down, pluged back into outlet. DONE!