Models > JGP330EP1 > Instructions

JGP330EP1 General Electric Cooktop - Instructions

Jump to:

All Instructions for the JGP330EP1
1 - 7 of 7
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Jorge from Tulsa, OK
Parts Used:
WB24T10071
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
electronic ignitors would not stop firing even when burner was off
first I removed all the srews from the burners that hold the glass cooktop. I then disconected the two wires from the damaged gas valves and replaced them all four with the new ones. After that I put it all togehter and work just fine and celebrated with a good cold beer.
12 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rusty from Schenectady, NY
Parts Used:
WB31M8, WB31M7, WB24T10071
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Gas Cooktop Igniter Wouldn't Shut Off
I removed the knobs, burner racks, drip pans (burn bowls) and then the glass cook top to access the gas switches. Selectively, I disconnected each to determine which switch was not working properly and then went online to order the part. While I had the stove apart, I decided to replace the burner bowls.
8 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Eve and from MIDLAND, MI
Parts Used:
WB24T10071
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
One burner would not ignite.
I replaced the igniter under the knob.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
pradyuman from Parlin, NJ
Parts Used:
WB24T10071
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Will not ignite
Shut of electric supply. Remove knobs and open top cover of cook top by removing two screws near each burner and replace switch.
3 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kenneth from Brooklyn, NY
Parts Used:
WB24T10071
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
burner would not ignite
The top is all glass so I took my time. There was about 12 screws and double sided tape. A lock washer holding the igniter on. It also gave me a chance to clean the hard to get to places. Your price was almost half of what a suppier here and getting it would have been 2 weeks compared to your 48 hours to my door. Thanks again
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from Pflugerville, TX
Parts Used:
WB24T10071
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
Ignitor on one burner worked intermittently
Cut off power to the cook top and confirm that power is actually off. In my case, this involved turning off a cicuit breaker. Remove all burner control knobs by pulling straight up. Lift off all grates, burner caps and burner heads. Remove two phillips head screws from each burner bowl. Pry each burner bowl up and unhook the ignitor wire. I labeled the wires to make sure I got them hooked back up right. Remove the four burner bowls by lifting them off. Make sure you remember where each goes so you can reinstall them in the right places. Pry up the glass cooktop and lift it off. I took the cooktop ouside and gave it a good cleaning. This plus cleaning around the cooktop and cleaning the burner bowls is what took most the time. Lift the defective switch off and disconnect the two wires. Align the flat in the new switch to the off position. Reconnect the wires and install the new switch on the valve stem. Reinstall the cook top. Reinstall the burner bowls making sure to reconnect the ignitor wires. Reinstall the burner heads, burner caps, grates and knobs. Turn the power back on and make sure everything works correctly.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dave from Bremerton, WA
Parts Used:
WB3K5040
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
The burner knob lost the retainer spring and would not stay in the burner valve.
Slide the new one on. Thanks you very much. The shipping was unbelievable, got it in less then 2 days.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JGP330EP1
1 - 7 of 7