JCP930BA2BB General Electric Cooktop - Instructions

I pulled out the range from the wall unplugged it from the wall then i opened the oven door and removed the two small screws on the front off the range and lifted the glass top and supported it with a 1/2" X 18inc wooden dowel, then i removed the two burner retaining screws with a small Phillips screw driver and removed the wires from the burner,
then i replaced the burner with the new one and reconnected the wires and placed the burner in to the two retaining clips and then tightened the two screws then i removed the wooden dowel and installed the two screws on the front bottom side on the range then i plugged in the range in and tested the burner then put the range back against the wall.

Removed the two screws that hold the range top down. Lifted up yhe range top and propped with a stick. Proceeded to mark the wires connected to the old burner so that the new one would be connected correctly. Removed the wires and then the two brackets that hold the burner in place. Removed the old burner and installed the new one. Connected the wires and resecured top to base. Turned on the current and it worked beautifully.

I pulled off the broken knobs and put on the new knobs. Effortless.

Very simple repair. Remove two screws to lift the range top. Then remove the two screws holding the element in place. Disconnect the wires from the old element, connect the wires to the new element. Reverse the procedure and you are done. Total time is anywhere from 15 to 30 minutes.

after removing the two screws that are just inside the oven, I propted the top open with the box that the part came in. I drew and labeled the wires as I took them off using a color coding. next I removed the two clips that held the burner in place and marked on the new burner exactly where the clips were attached. Replacing the clips was possibly the hardest part of the whole operation. When you replace the burner, don't forget to replace the insulation pad that is stuck one the metal where the conections are. I missed this and had to reopen the stovetop and slid it on after I was finished. Otherwise it went pretty smooth.

Turn off power to cook top. Remove 2 screws that hold the cook top to countertop. Lift complete cook top from counter and place diagonally across opening. Remove 10 screws that hold glass top to the component cabinet. Make a diagram of wiring to element. Disconnect wires. Remove 2 mounting brackets from bottom of old element and position them on new element and screw tight. Wire new element as diagrammed earlier. Replace glass top on component cabinet and reinstall 10 screws. Place unit back into counter opening and secure with 2 straps. Turn power back on. Stand back and enjoy your accomplishment.

I removed the screws from the underside of the stovetop, lifted up the top, propped it up to keep it from falling (using a large book), and removed the old burner by unscrewing it from the top and removing the wire connections. I then screwed the new burner into the top, and attached the wires back to the burner, dropped the top down (gently and carefully, of course), and screwed the top back down to the rest of the stove. It was fairly quick and painless. Although, putting the stove back into his position was not easy, but that was no fault of the stove!!

Removed unit from counter top. Opened to locate wiring diagram. Identified part snd searched on internet. PartSelect.com provided all missing information and had easy to follow instructions...confirming my initial assessment of the problem. Ordering was easy; delivery fast. Job completed.

1. Turned of circuit breaker to stove.
2. Take two screws out of control panel, and lifted it up.
3. Lay panel on side and removed knob.
4. Flipped panel over and take several pic for reference of each wire and location on back of controller.
5, Flipped panel back over and take needle-nose players and unhooked each wire tab on back of controller.
6. Flipped panel back over and take two screws out that hold controller on front of panel.
7. Flip the panel back over and remove the old controller.
8. Position the new controller in the panel and install the the two screws back to secure it to the panel.
9. Attach wires back to new controller based on your pic taken. Verify correct location to pic.
10. Attached panel on back of stove. Make sure all wires are secured inside of the control panel.
11. Turn circuit breaker back on and verify the burner is working correctly.

Removed stove top from counter, removed glass top by removing 10 phillps screws, removed control bracked, unplugged connectors(wires) on old control and plugged into the correct position on the new control, replace control on the bracket then reinstalled the stove top and placed the stove top back into counter.

Remove two screws hold cook top down: prop it open with piece of wood. (TURN OFF POWER TO RANGE FIRST!). Carefully make diagram of where wires go: remove and replace.. piece of cake!

Secured the power to the unit. Removed the burner knobs (5)and then lifted the unit from the granite counter top. Removed the screws (14) holding the glass top on and then removed the glass from the metal base. Removed the two screws holding in the selector switch, which was broke with a new one. Cleaned the metal base and installed the new glass top on it. Screwed the new top down. Cleaned the edge of the counter top and placed the unit back in with double face sealer tape. Placed the new knobs on for the burner controls, placed power back in service, tested job completed. Harry (

Just put it on the control post

opened oven door and removed two 1/4 " screws from range top. lifted range top and propped open like a car hood with a 1" diam dowel rod. marked on new element the wire color locations from old element and removed wires. removed the two small screws and clips that hold the element to the range top and removed element. Matched where the mounting screws locate to the new element. Installed new element in reverse order.

Only filled this out so people know how easy it was to do business with this company and how fast I received my order even with snail mail. I would definitely order from them again