JGP336BED1BB General Electric Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Thomas from Bloomsbury, NJ
- Parts Used:
- WB13K18
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner igniter needed to be replaced
Assumed the entire top of the range would have to be lifted off. Removed the three screws inside the top of the over door and then noticed the two screws holding the dish around the burner. They were tight and required WD-40 and then a sharp tap and came off.
Important: Notice the direction your old igniter is plugged into the wire. It is not clear and can go on either way.
Important: Notice the direction your old igniter is plugged into the wire. It is not clear and can go on either way.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Bakersfield, CA
- Parts Used:
- WB31T10006, WB29K47, WB29K44, WB29K41
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My wife wanted different color stove top grate & burner caps.
Called GE for part number crossover from gray to black and asked for an email quote. Called Parts Select for pricing, which was alot lower! Shipping took five days and less then $8.00 buck....now mama's happy!!!! Thanks for great frendly service from Mike in California.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jorge from Tulsa, OK
- Parts Used:
- WB24T10071
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
electronic ignitors would not stop firing even when burner was off
first I removed all the srews from the burners that hold the glass cooktop. I then disconected the two wires from the damaged gas valves and replaced them all four with the new ones. After that I put it all togehter and work just fine and celebrated with a good cold beer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- VINCENT from CYPRESS, TX
- Parts Used:
- WB13T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Spark module was not working correctly
I unscrewed the burners which was three screws per burner then removed gas control knobs and pulled up range top and un hooked the old module and replaced it with the new one two screws hold it in place and connected it the same way the old one was and put range back together and now it works perfect and saved me over $250.00 and part only coated around $40 with shipping great parts seller and I highly recommend partselect.com very easy fix thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aloha from Monterey, LA
- Parts Used:
- WB28K145
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacement cook-top, had natural gas orifices, needed propane
Three were simple screw out and replace with a nut driver. The warming burner had a smaller opeining which was too large for the nut driver. Had to remove shielding aroound it first. Simple, job. My mother did the last one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Irvine, KY
- Parts Used:
- WB13K18
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Electrode ceramic insulator was cracked
First I elevated range top, then removed cracked electride from connector pin. Installed new electrode and lowered range top and all was fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from LORDSBURG, NM
- Parts Used:
- WB1X500D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
No Spin Cycle
Lid Switch.
Rewiring connection.
Function is satisfactory.
Fan belt ordered is saved.
A 1970 Clothes Washer.
Rewiring connection.
Function is satisfactory.
Fan belt ordered is saved.
A 1970 Clothes Washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eve and from MIDLAND, MI
- Parts Used:
- WB24T10071
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
One burner would not ignite.
I replaced the igniter under the knob.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Dills burg, PA
- Parts Used:
- WB1X500D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom Heating element quit working after 30 years
Removed several screws and removed element. Replaced same. Total ten minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from las vegas, NV
- Parts Used:
- WB13T10046
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Sparking at 2 different burners all by themselves
Replaced Spark Module and adjusted igniters
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- pradyuman from Parlin, NJ
- Parts Used:
- WB24T10071
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Will not ignite
Shut of electric supply. Remove knobs and open top cover of cook top by removing two screws near each burner and replace switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Brooklyn, NY
- Parts Used:
- WB24T10071
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
burner would not ignite
The top is all glass so I took my time. There was about 12 screws and double sided tape. A lock washer holding the igniter on. It also gave me a chance to clean the hard to get to places. Your price was almost half of what a suppier here and getting it would have been 2 weeks compared to your 48 hours to my door. Thanks again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Longmont, CO
- Parts Used:
- WB13K18
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
would not ignite
It was so easy.I removed the old part with the new with pliers. Voila/// it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ram from Missouri city, TX
- Parts Used:
- WB03T10173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken knobs
Pulled the old ones out and slipped in new ones, all by hand. No tools are required.
The service provided by PartSelect was just GREAT!
The service provided by PartSelect was just GREAT!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Shelby Township, MI
- Parts Used:
- WB03T10173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Stove Top Knob cracked off because my can of Pam fell on it
Put knob right on, very easy. No tools required.
Was this instruction helpful to you?
Thank you for voting!