JXDC41001 General Electric Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Could not find the proper fitting drip pans.
Got the right ones from you"could not get them at Sears.com". All is well, wife is happy again.
Was this instruction helpful to you?
Thank you for voting!
drip pans worn out and rusted
just replaced drip pans. your company response was quick and delivery prompt. being an outdated range, am glad I could fine size I needed.
Was this instruction helpful to you?
Thank you for voting!
electric burner would not heat up
Pulled out the 8 inch surface element and then used a 1/4 inch socket to remove mounting screw for terminal block and pulled out block with attached wires as far as wires would permit. My range top does not lift up so I had to work thru surface opening but there was at least 10 inches of wire to pull out so it was not a problem. Cut existing wires at block, stripped 1/2 inch of insulation using my wire stripper pliers and wrapped wire ends of new terminal block and secured with wire nuts provided. Slipped on shrink insulation provided and applied flame from a hand held butane lighter. The instructional video on the web site was a great help. I may not have done repair without first watchng how easy it is. A cheap wire stripper is a great help. This supplier made it easy to select parts with fast delivery and complete the repair. Great source of appliance parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRED from Kenner, LA
- Parts Used:
- WB17X5113
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replace terminal block
Simple repair. Easy to do. It was disappointing to receive replacement parts which were not ceramic terminals as depicted and described in words, but plastic and therefore will need to be replaced again soon. In addition the shrink tube was not large enough in diameter to cover the wire nut, both of which were provided with the replacement terminal. Part # PS232646 is not ceramic, but plastic which does not fair well in high heat applications.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from El Paso, TX
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
heating element would not heat to red hot.
unplugged and installed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES from STATE COLLEGE, PA
- Parts Used:
- WB17X5113
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Contact Burnout Inside Terminal Block
Pull out oven/range unit. Lift range top all the way up. Remove old terminal block. Make electrical connections using supplied wire nuts & heat shrink tubing. Heat shrink. Replace range top. Install coil burner & burner pan as unit. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from Fayetteville, WV
- Parts Used:
- WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the center of the element had broken
just pulled the old one out and replaced with new one. very easy
Was this instruction helpful to you?
Thank you for voting!
My old drip pans were no longer cleanable
Pretty simple really. Just pulled out the heating coils/elements, lifted out the old drip pans, dropped in the new ones and "plugged" the coils back in and Presto! New drip pans,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Montgomery,, AL
- Parts Used:
- WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
welded supports for the surface elements were broken
unplugged the broken elements and plugged in the new ones. Took about one minute. Tools used: hands and fingers.
Was this instruction helpful to you?
Thank you for voting!