JP384 9T1BL General Electric Cooktop - Instructions

After unplugging the range I took the rear sheet metal panel at the top off with a nut driver to expose the wiring connections. The next step was to remove the single screw holding the old part in place. (under the drip pan) Once free I snipped the old part from the wires and then taped the new female ends to the old wires with black electrical tape. From rear I carfully pulled the old wires through the back until I could reach the new wiring connections. Unplugged old, plugged in new and replaced the rear metal cover. Then I put the screw that holds the new block bracket in place, replaced drip pan, and burner. The final step was to plug the range back in and check to see if the burner worked. It did and I was done. Approx. 5 minutes

Removed by slightly wiggling out of the coupling. No tools needed, seriously, (and I'm a contractor). Basically, pull out and snap back in.

First I unplugged the stove, then lifted the stovetop, then took off the top panel on the back and disconnected the two wires. Then unscrewed the terminal block and put the new one in its place. Lowered the top inserted the eye and replaced the back panel. Works great!

This is the second time in a few months that I replaced this terminal block, so I made sure the contacts were clean and smooth. I also made sure the contacts were completely inserted in the block.

Removed the burner coil.
Unscrewed the terminal block.
Pulled out the stove and disconnected the 220 Volt service at the plug.
Removed the back panel at the control knobs.
Detached the wiring to the control knob and pulled thru the back panel.
Wiring mostly visable to the front 8 inch burner.
Replaced wiring and mounted new terminal block.
Tested the burner for a few seconds.
Replaced back panel and set stove in place.
Saved $150 dollar service call.

This appeared to be an easy fix, but turned out to be more involved than I planned. The hard part was pulling the range/microwave oven assembly away from the wall so I could remove the back panel and see how the new terminal block wires connected up to the switch/knob that operates the burner. Extracting the whole range unit required me to use a floor jack to raise the leveling feet of the range above the edge of my floor tile so I could slide the unit out. Once away from the wall, I used a nut driver to remove the back panels. Next surprise was the new terminal block wire connectors were not the same type as the old block's connectors (flat vs. male pin-type). Rather than let the scope of this job creep to include a whole new connector rig, I opted to splice the new terminal block wires onto the existing wires that led up to the control knob. I used professional splices and a crimping tool to secure the wires. After checking the new installation was sound and operational, I slid the whole range back into place. Attaching the new terminal block to the range top was a piece of cake, but getting the damn oven out into open space where I could work on it was bear. But, hey, I learned a few things, one of which is that when a homeowner decides to retile their kitchen, make sure you run the new tiles all the way under the range and not just up to the front edge of the oven. I can see why this was done - to avoid having to remove the oven during the retiling - but it creates an obstacle for whenever the oven needs to be pulled away from its location. The last tool I imagined I would need for this repair was a car jack. The Parts Select part worked fine.

I handed it to my wife and she slipped it in.

Removed old surface burners and replaced them by plugging in the new surface burners. Now they work GREAT! Parts ordered and received with-in 3 business days. Fed EX delivered parts in good order very quickly. We recommend PartSelect.com

I unplugged the burner, lifted the old drip pan out, put new drip pan in, plugged burner in. The stove looks brand new and it took less than 2 minutes.

I am a 62 y/o single female and was able to make this exchange of parts with ease. The toughest was getting the old terminal's wire clips free from years of gunk! I was pleased with the ease of installation and that it really worked afterwards. By the way, thank you Parts Select for getting this part to me very quickly. If a novice can diagnose, find the correct part and install it with success then anyone could do the same.

I just removed the range elements and old bowls, placed the new bowls into the range top, and inserted the heating elements. What surprised me was the quickness in filling the order. I had the new parts the next day! Great!

Removed existing surface element and replaced with new element.

P.S.

Part Select service was excellent.

Only instructions I have has nothing to do with installation. But I'd like to suggest that you find a better shipping method. Placed my order on Feb. 7, received message later same day that it'd shipped. I didn't receive it until Feb. 16th -- very poor delivery service.

I first unplugged the stove (alternatively, shut off the breaker). I unscrewed the terminal block screw from the stove top (after removing the stove element and burner bowl). I got in behind and removed the six screws in the sheet metal panel. Removed the panel. Unplugged the terminal block wires for each unit, one at a time, and immediately plugged in the new unit wires (after threading the wires up under the control panel). Wire polarity doesn't matter. Secured the panel temporarily with a couple of screws. Replaced the burner bowls and stove elements in the new terminal blocks. Plugged in the stove and tried each unit. Worked great! Secured the remaining screws in the rear panel and moved the stove back into place. Thanks so much!

I first removed the unit by pulling gently from connection. Replaced the new one in that same manner - simply inserting into connection.

Very easy, I'll probably try it again soon.

Removed 4 screws holding the control panel removed the receptacle wires removed the screw holding the receptacle in place. Inserted the new receptacle screwed it in inserted the the wires to control knob. Screwed the control panel in place. Replaced 2 burners and 2 elements with in a half hour. Simple. Received the parts with in a few days. Will order from here for now on. Before we ordered looked for parts everywhere could not find them. Thanks