JXDC410N3BC General Electric Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Arthur E. from St. Louis, MO
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I ruined old unit
Removed old, and replaced with new, heating element! Maybe 10 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Richmond, VA
- Parts Used:
- WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed new electric element
A breeze! Part was perfect replacement, snapped in place without tools, and heated almost immediately.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from Cincinnati, OH
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A teapot melted on one of two working burners
Pulled the old surface element out and plugged the new one in. Took all of 45 seconds!!!!!
It's nice to know that one can still get replacement parts for 50 year old stove tops!!!!
It's nice to know that one can still get replacement parts for 50 year old stove tops!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Guilford, NY
- Parts Used:
- WB17X5113
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My heating element will not work
I turned the power off to the stove (very important). then I unplugged the heating element from the terminal. I then unscrewed the terminal from the range top and pulled the terminal through to expose enough wire to do the job. I then proceeded to cut one wire from the old terminal and twist the new wire onto the wire that goes to the switch. Then I capped it off with the electric cap that came with the new terminal. then I covered the exposed wires with the sleeve that came with new terminal. Then I did the same exact thing for the second wire. After that was all done I put everything back together and turned the power back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Gloversville, NY
- Parts Used:
- WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burned-out six inch electric stove- top burner
Removed the old and slipped in the new.No problem and it works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LISA from GLENDALE, CA
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Electric stove 8" burner needed to be replaced
Installation took 30 seconds. Your website was easy to use & the part received was just as described. It arrived beautifully wrapped & in just a few days. ABSOLUTELY AWESOME!I will recommend your site to everyone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeannette from Haskell, NJ
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner heating coil element would not get hot.
I pulled out the heating coil and pushed in the new coil. I turned the stove top on and heard a sound like "dzzzt". I immediately turned off the burner and waited for it to cool, then pulled it out. The part had a burn melt on one side of the end prong. It turns out that the part that the burner plugs into needs to be replaced. Actually, the stove top is over 20 years old and my landlord will have to replace the whole unit. So it turns out that I didn't need to order a surface element after all, but it was very easy to install!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARLENE from EUGENE, OR
- Parts Used:
- WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
element broken at contact point
ordered new surface element and pushed in to conector turned on switch to test and works fine thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois from Sarver, PA
- Parts Used:
- WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plug-in surface element was covered with a melted on forever microwave plate
Just put it right into the receptacle. I want to add...we had gone to our local appliance store and brought home a wrong-size unit. Got online and your website came up. It was easy to find the correct part, ordered it and it arrived 3 days later. I have already recommended your website to 2 of my friends. One very good experience!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Dallas, GA
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner not working.
I pulled the old burner out and slid the new one in it's place. Turned on the eye to make sure it worked. Felt heat in a few seconds and turned off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DEBRA from DULUTH, MN
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I Ruined My Burner -- This Was A Solution For Me...
I simply pushed the new burner into hardware. I then tested it to see if it works. . .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Chesapeake, VA
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The burner stopped working
After checking at local appliance stores and unable to find the bunner I went online looking. I found this site and there it was. I ordered it, received it within two days, took the old one out and the new one in. As my granddaughter says, "easy peasy lemon squeeze". It took all of five seconds and I'm cooking again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Frederick, MD
- Parts Used:
- WB32X5076
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Existing drip pan was burned & beyond cleaning.
Unplugged the burner unit. Removed the existing drip pan. Installed new drip pan in place & re-plugged the burner unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from San Antonio, TX
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Surface element burned out
Removed old burner, plugged in new burner. Turned on electric and everything worked fine. I was concerned that I would not be able to get the correct burner since my stove is approximately 30 years old and General Electric no longer stocks replacement parts. The new surface element was manufactured by General Electric and had the correct replacement number on the package. Thanks Part Select.
Was this instruction helpful to you?
Thank you for voting!