RTG650-P1131487ND Caloric Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Billy from Martinsville, IN
- Parts Used:
- WP3185804
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
There was a crack in the porcelain not letting it spark
I used a screwdriver to pry the electrode assy. out of the burner. then disconnected the wire.
Then just connected the new electrode and place the assy, in the burner.
Then just connected the new electrode and place the assy, in the burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from San Bruno, CA
- Parts Used:
- WP3185804
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
broken ignitor insulation; repeated sparking after burner lit
Disconnected gas & electric connections; lifted unit out of countertop onto padded table upside down. Unscrewed ~16 sheet metal screws for access. Removed bad ignitor by driving off retaining clip. Had to remove burner (3 screws) for access to install retaining clip on new ignitor. Reassembled, reinstalled. Works like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wade from Jacksons Gap, AL
- Parts Used:
- WP3185804
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Spark Ignition Electrode was not sparking properly
Used a pair of pliers and pulled firmly on ignit. elect. till the retaining clip pulled off the bottom of the elect.The wire pulled off the bottom of it and I had to use a long- thin- nose set of needlenose pliers to pull the wire out of where the elect. came out.Plugged wire in place and snapped electrode back in place without using the retainer clip.Works great.Thanks Wade
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shelly J from KAPLAN, LA
- Parts Used:
- WP3185804
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
igniter on top right front burner was shorting out,it would click but not ignite burner
removed igniter and found porcelin split in half. JB welded both halves and put back into slot ,works fine now. Bought two extra in case.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Hendersonville, NC
- Parts Used:
- WP3185804
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
stove gas burner would not light?
TURN OFF THE GAS SUPPLY & POWER TO THE STOVE. Disconnect the gas line & power source to the stove. Remove the complete counter top stove and place it upside down on a flat surface to enable you to remove all the surrounding small screws with a nut driver, then separate the bottom from the top accessing the retaining ring holding the ceramic electronic Ignition in place, remove the electric wire from the the old igniter. The most difficult part of the job was removing the retaining ring and installing the new ring.Job successfully completed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHARLES from CHICAGO, IL
- Parts Used:
- WP3185804
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no ignition on right frt burner
removed one screw lifted he brner took retainer off unpluged the igniter it had broken porcelen reversed the procedure everything worked fine
Was this instruction helpful to you?
Thank you for voting!