ETR645 Caloric Cooktop - Instructions

Removed heating element, installed new drip pan, replaced heating element. Was amazed at fast delivery - ordered in afternoon, arrived fed ex next morning!

I noticed that one of the burner blocks was completely burned and the others were corroded. I ordered blocks for all four burners. Installation was easy except for one block. The screw holding the bracket to the range top was completely corroded in place. I used a correct size easy-out, which is a left hand tap and drill, to remove the screw. That took about five minutes, including tracking the easy-out down in one of my many toolboxes. The entire replacement of four blocks took about one and a half hours. Stove top cooks like new on all burners! The part kit had all the right parts and they fit like a glove!

Turned off stove breaker. Unscrewed burner from stove top, took out burner and spill pan. Lifted top of stove, cut the wire as instructed and put all parts together as instructed. Placed everything back together as instructed. I did it myself!

Ordered wrong part at first caused me to blow out two elements. With the help of PartSelect I was able to get the right surface block terminal and replaced both of them, then found out I had a bad switch, they got the switch within 2 days I had my stove working good again. Thanks to PartSelect. Also watched the video which was very helpful ML

Remove heating element coils. & old drip pans. Install the new drip pans and reinsert the heating elements and insure all elements were level. For aesthetic reasons I replaced all the drip pans - 2 x 8" & 2 x 6".

After turning off circuit breaker to the stove, I removed all surface units , removed the 4 screws holding the top and lifted up. The plug in was burned out (the wire was burned). Look at the old plug-in so as to be able to match the new one and insert the pre- crimped end of wires into the block and the block into the metal holder that matches your old one. (The kit comes with 2 different metal holders)After this, cut out the old wires and wire nut the new wires with the stove wires. Put shrink wrap protector on the wire nuts and heat to shrink it tight.attach the block to the stove top and wa la its done. Very easy.

I removed the burner element, then the drip pan. I took off the old block. Then I had to strip the old wires. Then I put on the heat sleeve, then attached the new wires to the old wires with nuts. Put heat sleeve over this and heated with lighter. Then put everything back together.

Unscrewed screw holding bracket. Used side cutters to cut wires. Replaced the bracket, put the shrink wrap on wires, twisted wires together and held with wire caps. Shrunk the wrap with lighter. I'm a 67 year old female.. No problems.

I removed the entire burner assembly to avoid having to turn things off at the breaker - the whole assembly can be removed completely from the stove I had. Once it was out and disassembled, the toughest part was putting the new wires into the new block correctly. Once that was done, I had to select the right mounting bracket - there were 2 in the kit. Easy, just attention to detail. The rest of the instructions were easy to follow, re-doing the wires. The re-assembly was trivial, and it worked first time!

Remove old drip bowl from the range and put a new one back.

I will begin by saying that not only will I continue to order my parts from PartsSelect, but I also highly recommend this business. If you call Whirlpool be careful that they forward your call for parts to some preferred vendor, which a customer might assume is Whirlpool but it is not. PartsSelect is the same type of business, but with outstanding customer service. With regard to the drip pan, Whirlpool had not updated the part number for these as I found out when i called them. Whirlpool no longer uses the drip pans without the holes which is a serious problem since this could be hazardous to the owners of these ranges if you are forced to purchase the drip pans with the holes in them. That said, I ended up keeping my old drip pans, because if you spill grease under the new ones with the holes in them and since the range design with the fan built in on the top does not allow you to lift the top to clean under the pans, you could end up with a grease fire. This is not the fault of PartsSelect and they handled my order in a manner that I would give them a rating of exceptional for customer service.

After carefully inspecting existing burner receptacles, I unscrewed them, raised and propped stove top. Determined which bracket to use from new kit and proceeded to cut and strip wires, twist ends together with supplied ceramic caps and heated shrink wrap on that junction. Works great. BTW got parts in 2 days in great shape and good directions.

It was so easy to order a new one from your company. And it arrived in less than a week! I slipped it into the electric outlet and it worked perfectly. THANKS. Wanda Major

Used new plug in coil burner.