AKGD3060E (P1131630N E) Amana Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Don from East Dundee, IL
- Parts Used:
- 32020101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
two burners were not sparking
Philips is all that's needed. Remove the burners (2 screws each) lift off top of stove, replace the ignition module. put all back together and your done. Local parts store wanted $80+ for the module. PartSelect only $50 total cost and it hit my mailbox in TWO days! Thank you PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from hillsboro, OR
- Parts Used:
- WPY0316773
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
none of the burners would light
I removed all 4 burners 2 screws holding each,replaced the ignition module,wire for wire,reassembled after cleaning the stovetop.I,m my wife's hero.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from New Albany, IN
- Parts Used:
- 32020101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Stove top burners would ignite every time
Removed two screws per burner. Unhook wires. Putting back broke slide on connector and had to replace. That took longer than the whole job. I ordered the part before 3:00 pm and it was at my house tjhe next morning which was hard to believe. The instructions that come with part made no sense what so ever. Thanks for the quick service and I will be back.
Dave
Dave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Ottawa, IL
- Parts Used:
- 32020101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burners wouldn't light
Unscrewed the burners,lifted the top up,unplugged the burners.Took out the bad module,making sure of where the wires went and put them in the same spots on the new module,reconnected the burners lowered the top screwed the burners back in and the burners lit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Woodstock, IL
- Parts Used:
- WPY0316773
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Replace Ignition Electrode gas range
Wow, ordered the part here and it arrived in 18 hours!! Job was fairly straight forward but the screw holding it in place was corroded and stuck. Several heating and cooling cycles with a torch and some spray lube and lots of patience and I finally rocked the screw lose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stanley from St. Louis, MO
- Parts Used:
- WPY0316773
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench set
The spark was no longer igniting the burner
The earlier reviews said very easy and 15 minutes for beginners. They were right on, except I could not get the old screw out no matter what I tried. I eventually had to drill it out and put in a self tapping new screw. This was a first for me. Then it took 15 minutes or less and works fine again. Hopefully next time someone will tell me how to get that old screw out faster.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronnie L from Hammond, IN
- Parts Used:
- 32020101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ignition Module failed
First I removed the knobs on the range, then the front cover and then removed the two screws that hold each burner in place. I removed the top and removed the Module and started replacing the burners and front ocver and knobs. The Module worked GREAT. Thanks for your fast service in getting me the parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Sonora, CA
- Parts Used:
- WP7504P109-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner would not ignite even with gas flow spark and clicking.
Removed two screws and disconnected the ignition wire. Then connected ignition wire to new burner and installed two screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- neil from foxboro, MA
- Parts Used:
- 32020101
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
top burners would not light
Removed the top, 4 screws and pulled the contact wires off. Replaced the module and connected the contacts. Put back the screws and the top. When the stove was new it did not operate properly and we had a technician out, but naturally it worked for him. For the past 14 years intermittent operation has been agravating me. With the new module the burners have never worked so well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Philadelphia, PA
- Parts Used:
- WPY0316773
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
cracked ignitors (2)
No problem removing the burners. Removing the old initors was a different story. The tiny screws that hold the ignitor in place were baked in and could not be removed with a screw driver. I drilled them and tried to use an easy out to no avail. The screws are very short so I had to use care not to drill thru the burner. Both screw heads did snap off. I resorted to a hi temp epoxy to secure the ignitor flanges to the burner and now the all burners ignite as designed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Owensboro, KY
- Parts Used:
- WP315600B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cosmetic replacement of stove top burner bowls.
Easily replaced the stovetop burner bowls by removing the old ones and replacing with the new ones.
Parts Select provided easy online ordering and was nearly one-half the price of other online suppliers.The quality was excellent!
Parts Select provided easy online ordering and was nearly one-half the price of other online suppliers.The quality was excellent!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marv from Eugene, OR
- Parts Used:
- 32020101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
ignintion spark was very weak, burners would not light
removed two screws from each burner, removed ignitor wires from burners, pulled range top removed old module and inserted new reattaching wires for four burners, switch and power to new module. reset top, attached wires to burners and reinserted screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from Homer Glen, IL
- Parts Used:
- WP31760504B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed new knob
PartSelect is great. They had the knob for my stove. They said shipping would be 5-7 days, no big deal. BUT, I received it the next day via FedEx. Great! Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Lake Oswego, OR
- Parts Used:
- 32020101
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Gas cooktop burners would not light
We lived with the problem by using a long-reach butane torch lighter for three years after an appliance repairman told us the problem would be very costly to repair. Finally, we found the likely suspect when we happened onto PartSelect's website- the spark ignition module. The cost was just over $81 plus shipping. We ordered on Wednesday, it arrived on Friday by FedEx, and I installed it on Saturday morning. All the parts were included, the instructions were clear and complete, and, best of all, our range now works as it should. We couldn't be happier. Thanks, PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carroll from Lynden, WA
- Parts Used:
- 32020101
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
no ignition at burners
Removed burners and top cover to access ignition module.
Remove and replace module and reassemble stove.
Remove and replace module and reassemble stove.
Was this instruction helpful to you?
Thank you for voting!