AKT3040E (10) Amana Cooktop - Instructions

Remove Ceran Galss top by removing hex screws below the rim. Also remove the two opposing screws in the center of the downdraft opening. Ceran top comes off easily now.
The instructions with the new switch were very poorly written, so here is how I got the new switch to work:
Attach the black wire(s) from the old switch (terminal 2) to the new switch terminal P1. Also attach the jumper cable to P1 and "jump" it to S1.

Attach the orange wire (old switch terminal 5) to S2
Attach the yellow wire (old switch terminal 4) to 4a
Attach the tan/(white?) wire (old switch terminal 3) to terminal 4 on the new switch
Attach the single red wire from the right front element to terminal 2 on the new switch.
Attach the 'compound' red wires (the ones that come from the left rear/outlet connection and is also attached to the right rear switch) to terminal P2 on the new switch.
There is no need to seperate the compound red wires as the instructions might lead you to believe.
Good Luck

The repair itself was very easy. “How to connect” was very hard to get.


To get access to the switch, unscrew 2 screws from each side of front panel and then 4 screws from the bottom of it (open the door first). Have a box or a small table about 30” high to use it as support for the front panel.

The end result (colors for the Right Front- R.F.- burner) : Old label -> New label

1. Double RED: N -> P2 (incoming power, Line 1)
2. Single RED: N -> 2 (to Inner AND Outer heating elements common wire)
3. Single BLK: L1 -> P1 (incoming power, Line 2)
4. Single TAN: H1 -> 4 (to the Inner heating element)
5. Single YEL: H2-> 4a (to the Inner heating element)
6. Single BLK: P -> S2 (to the R.F. indicator control light)
7. Attach jumper black wire (included with new switch) from P1 (P1 has two connectors close together) to S1.

Done.

Turned off power to unit.
Tilted up Glass top and removed two screws holding rear hinges to range. Then I unplugged wire harness from lower range and placed the Glass top facing down on counter top with towel for cushion. Removed 1 screw holding center of burner to support frame, two alignment screws on perimeter, and two screws holding support frame to glass top. This allowed me to slide out the old element with all wiring connections intact.
Placed the new assembly in same location under support frame, noting numbered positions of two alignment screws from old unit. This is necessary to properly align heater to surface glass. Replaced all screws connecting burner to frame. Then I removed each wire one-by-one from old unit, reconnecting to same location on new unit.

Replaced top in reverse order from removal. Powered on the circuit breaker and verified proper operation of dual unit with large/small selecttor switch. Total time to repair about 30 minutes.

This is not at hard as it seems; I followed the first guy's story and ignored the colors because mine were different. I did have to split the combined red wires, intimidating at first but once I split them it was down hill.
I did have to use the jumper wire.

Follow
Appliance Repaired: Jenn-Air Range/Stove/Oven/Hood

Model: cve3401b

Age Of Appliance: 5 - 10 years


Remove Ceran Galss top by removing hex screws below the rim. Also remove the two opposing screws in the center of the downdraft opening. Ceran top comes off easily now.
The instructions with the new switch were very poorly written, so here is how I got the new switch to work:
Attach the black wire(s) from the old switch (terminal 2) to the new switch terminal P1. Also attach the jumper cable to P1 and "jump" it to S1.

Attach the wire from old switch terminal 5)to S2
Attach the wire from old switch terminal 4 to 4a
Attach the wire from old switch terminal 3 to terminal 4 on the new switch
Detach the 'compound' red wires from each other.
(The ones that come from the left rear/outlet connection and is also attached to the right rear switch) to terminal P2 on the new switch.

I attached common female connectors.
Attach the newly split single red wire from the right front element to terminal 2 on the new switch.

One note:

Before you remove the four screws that hold the four swtiches down make sure that you use a sharpie and mark the switchbox location. You will notice that it is difficult to get them to line up again with the holes in the cooktop.

Thanks partselect.com!

I removed only 3 screws that allowed me to lift the glass top on the stove. I removed the burner and I could see where it short circuited. I ordered the new burner element. After it arrived I replaced it by moving the wires from the old element to the new element, and put it back together.
I am sure that I saved at least $200 in "labor".

Pulled stove out and unplugged it (energized wire at burner even with burner turned off) Removed screws to lift cook top Removed burner support brace Removed three screws to remove burner Removed connections from old burner, installed on new burner Replaced screws in burner to brace Replaced burner brace Lowered cook top and installed screws Plugged in stove and pushed it into space

Turned off circuit breaker and unplugged. Opened oven door and removed 3 screws holding the range top to the range. Lifted top and proped open with a wooden block. Removed all 5 wires to the element and drew a diagram of where they came from noting the color code. Removed two screws holding the bar that supported the element
and dropped slightly while removing the two standoff screws holding the element in place.
slide the element out. The problem was that the element received from partselect.com did not physically match the terminals on the original. this required me drill out a brad on the terminal block cover to see how the terminal block was wired. I discovered that the different color wires on the old element went to physically different terminals on the new one. This was even though I had returned the first element received, got a new part no from matag and reordered.
there are tiny markings on the terminal block that helped show the way. Be sure to find them and rewire according to these markings. 1a 2a 1b 2b as the terminal locations may be different.
I am happy with the partselect,com and their attention to trying to get me the exact replacement.
Also happy with their return policy.

I turned off the circuit breaker to the cooktop. I had to remove aluminum tape from the downdraft fan so it would disconnect from the exhaust duct. I noticed that I had a long enough electrical connection so I could just lift the cooktop up out of the opening and support it at the corners with shims. I removed all the knobs from the cooktop and then removed the 1/4" sheet metal screws that held the ceramic top to the base. My cooktop had a downdraft fan in the center which has 2 phillips head screws that at first I didn't see, but once I removed those, the ceramic top came off and exposed all the inner workings. I removed the 2 phillips screws holding the switch and then swapped each wire from the old switch to the new one. After that, it was just a matter of reversing the process to get everything back in working order.

TURNED OFF POWER TO STOVE Removed 5 Knobs, 2 screws that held bad switch.
Removed 4 screws and lifted panel up and forward to expose switches. Adjusted spring tension on knob stem to hold knob ( stem in new switch slightly smaller) removed wire from defective switch one at a time and fastened to new switch in sequence. Reassembled and turned power on. Defective switch had stuck contacts making it full hot.

First, disconnected downdraft fan from ductwork below stovetop. Pushing from below, was able to lift entire stovetop assembly up to expose nuts holding glass top to the underlying burner assembly. used 2 lengths of 2x4's under the whole stovetop assembly to hold it up while I worked. Unscrewed all hex nuts and 2 screws at top of downdraft opening and easily lifted glass top off, exposing elements below. Removed a few screws holding defective switch in place. I then moved one wire at a time from the old switch to the new switch. I actually followed directions of another partsect customer. His step by step directions for the wiring was invaluable. Worked perfectly. My wife and daughter are very impressed.

First we turned off the power to the range top. Then propped the range top on small planks of wood in order in order to get to the 12 to 15 screws that held the top to the base. Once we had the top (glass) removed, we removed the four screws holding the bracket that held the front and rear elements. We then removed the bracket and elements, turned the bracket and elements over to remove the two screw type legs that held the dual element. Once the dual element was loose we disconnected the wires and reconnected to the new element. Then reversed the procedure to reinstall.

Isolated circuit by disconnecting cooktop breaker.
Disconnected blower duct, raised cooktop above the countertop to access screws holding the glass surface.
Blocked in place--no need to completely remove cooktop.
Removed screws around top of pan with 1/4-inch nut driver--only need to remove any screws close to top of pan and glass surface.
Lifted off glass surface.
Dual burner switch bracket needs to be removed to access switch and to disconnect wire harness connections.
Note there was one screw holding bottom of bracket which was hidden by the wire harness.
I was concerned with connections from other reviews; however, in my case, the switch and connections were identical to the original--no problem.
Reinstalled bracket and glass cooktop--need to remember flange location (inside versus outside) to assure easy alignment of screws. Drop cooktop back into countertop and reconnect blower duct.
Powered back up and dual burner now fully functional.

Followed the first persons instructions and they worked perfectly including using the jumper wire.

I had an electrician do it. The instructions were horrible. He followed the instructions from your web site. The cooktop was not on an island so he could not remove all the screws to release the top so he worked with the top propped up. When he finally got the connections on, the small burner would not work only the large outer burner is working. He went on the computer to see if he could get more information but was unable to find any information.

Removed glass top from stove by taking out hex screws which secured glass top to stove frame. There are two phillips head screws inside the exhaust as well. Removed two phillips head screws which hold the burner switch in place. With a sharpie pen I marked the color coded wires on the faulty switch. Removed wires from the faulty switch. Replaced new switch using the old switch as a guide to insure that wires were connected properly. Secured new switch and glass burner top reversing above procedure. Problem solved. Note: The white dot on the control knob did not line up properly with the off position. Black out white dot and make a new one in the proper spot on the knob.