ACC3660AS (PACC3660AS1) Amana Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- HUY from ALISO VIEJO, CA
- Parts Used:
- WPY0316773
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Broken Electrode, no spark
Remove 2 screws holding the top burner. Remove 1 screw holding the electrode. Remove electrode from wiring using plier. Install new electrode and top burner
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Friendswood, TX
- Parts Used:
- WPY0316773
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner would not ignite when control in "light" position
Remove the two screws from the burner assembly (on top of the burner). Lift burner assembly from the cook top. Disconnect the electrode wire from the electrode. Remove the screw holding the electrode to the burner assembly (on bottom of burner). Install the new electrode and attach the electrode to the burner assembly. Attach the electrode wire to the electrode. drop the burner assembly back into position on the cooktop. Attach the burner assembly using two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Livonia, MI
- Parts Used:
- WPY0315768
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Two of the four burners would not ignite when lighting the stove.
I thought the problem was with the ignitors/burners since they appeared to be worn. As it turned out, I needed the spark ignitor, which is a "brain box" located under the range cover. It connects all of the ignitor/burners and sends current to the ignitors to give it the "spark" to ignite the gas. It was really easy to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Greenville, NC
- Parts Used:
- WPY0315768
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
gas burner wouldn't light
replaced top burner - in theory simple, but severe rusting of two screws holding the burner required drilling and extracting with a screw extractor. The screws broke requiring that the entire burner pan assembly be taken apart to remove the broken nubs of screws from behind with vice grips. Recommend that you have proper sized pan head screws available when you start job so it can be finished in one sitting. Burner starts perfectly now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Santa Rosa, CA
- Parts Used:
- WP315600B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The burner bowls were damaged due to wear.
No tools were needed; the old burner bowls were taken out and replaced with the new burner bowls. I would like to say the service was great from PartSelect. com. I was so happy I was able to find replacement bowls for my older drop-in range that I ordered a second set to keep for future use. PartSelect.com sent the replacement bowls quickly, and the order was processed very efficiently. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TODD from PALOS HEIGHTS, IL
- Parts Used:
- Y0316913
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
knob stem broke off switch
I had to remove the 18-22 screws that held in the top of the stove. Then remove the nut that held the switch in place. I took a pictures as I went with my camera phone. That way I remembered which wires went where. Since there was a two day lag getting the part, i was afraid that I would forget. Once I received the part, I just reversed the process. Hardest part was getting the stove top to fit back, as the rubber insulation had expanded a little.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- D, from Imbler, OR
- Parts Used:
- WPY0316773, Y0316389
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Gas burner wouldn't ignite. No Spark
Replaced the spark igniter which had been broken.
Great response and shipping time, even though one part was back ordered. Works perfectly!
Great response and shipping time, even though one part was back ordered. Works perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Derek from Seattle, WA
- Parts Used:
- WP7504P109-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
One of the burners would not autolight, had to be lit with match
This was VERY easy and I've never worked on this type of appliance before.
First, take off the grate, thermal plate, etc that are resting on top of the stove (this is all the stuff you take off to clean the stovetop).
Then, carefully unscrew the two screws holding the burner to the gas pipe. Grab the screws and set them aside so they don't fall back into the stove, then pick the burner up off the stove.
once you have the burner a few inches above the stove surface, wiggle off the single wire by grabbing it on the metal part (not by the wire) and gently wiggling it off.
Grab new burner, push on wire and sit it on stove, use a finger in the gas pipe to align it and put the two screws in. you're done.
First, take off the grate, thermal plate, etc that are resting on top of the stove (this is all the stuff you take off to clean the stovetop).
Then, carefully unscrew the two screws holding the burner to the gas pipe. Grab the screws and set them aside so they don't fall back into the stove, then pick the burner up off the stove.
once you have the burner a few inches above the stove surface, wiggle off the single wire by grabbing it on the metal part (not by the wire) and gently wiggling it off.
Grab new burner, push on wire and sit it on stove, use a finger in the gas pipe to align it and put the two screws in. you're done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Glenwood Springs, CO
- Parts Used:
- WPY0316773
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Ignition electrode broke
Removed the two screws that hold the element in place. Disconnected the wire to the electrode. The screw holding the electrode to the burner plate would not unscrew so I had to drill out the screw in order to replace it with the new ignition electrode. A little more time involved but if the screw would have come out it would have been a 10 minute job.When I ordered the part from you it came very quickly and I will certainly use you again when I have any other issues.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from hillsboro, OR
- Parts Used:
- WPY0316773
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
none of the burners would light
I removed all 4 burners 2 screws holding each,replaced the ignition module,wire for wire,reassembled after cleaning the stovetop.I,m my wife's hero.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Woodstock, IL
- Parts Used:
- WPY0316773
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Replace Ignition Electrode gas range
Wow, ordered the part here and it arrived in 18 hours!! Job was fairly straight forward but the screw holding it in place was corroded and stuck. Several heating and cooling cycles with a torch and some spray lube and lots of patience and I finally rocked the screw lose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Philadelphia, PA
- Parts Used:
- WPY0316773
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
cracked ignitors (2)
No problem removing the burners. Removing the old initors was a different story. The tiny screws that hold the ignitor in place were baked in and could not be removed with a screw driver. I drilled them and tried to use an easy out to no avail. The screws are very short so I had to use care not to drill thru the burner. Both screw heads did snap off. I resorted to a hi temp epoxy to secure the ignitor flanges to the burner and now the all burners ignite as designed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stanley from St. Louis, MO
- Parts Used:
- WPY0316773
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench set
The spark was no longer igniting the burner
The earlier reviews said very easy and 15 minutes for beginners. They were right on, except I could not get the old screw out no matter what I tried. I eventually had to drill it out and put in a self tapping new screw. This was a first for me. Then it took 15 minutes or less and works fine again. Hopefully next time someone will tell me how to get that old screw out faster.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Sonora, CA
- Parts Used:
- WP7504P109-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner would not ignite even with gas flow spark and clicking.
Removed two screws and disconnected the ignition wire. Then connected ignition wire to new burner and installed two screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Owensboro, KY
- Parts Used:
- WP315600B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cosmetic replacement of stove top burner bowls.
Easily replaced the stovetop burner bowls by removing the old ones and replacing with the new ones.
Parts Select provided easy online ordering and was nearly one-half the price of other online suppliers.The quality was excellent!
Parts Select provided easy online ordering and was nearly one-half the price of other online suppliers.The quality was excellent!
Was this instruction helpful to you?
Thank you for voting!