LEC1330AAB Admiral Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Milton, FL
- Parts Used:
- 7403P239-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Front burner would not heat properly.
Ordered a front burner but it was not the right size. Ordered a switch after local dealer said I had a bad switch. Ordered a switch from Parts Select and received it the next day. Works good now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Manchester, MI
- Parts Used:
- 7403P239-60, 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Front 8" stove burner got excessively hot at any setting
Performed repairs just as you directed. Everything went in in without a hitch. All the parts fit well and seem to be working fine. Wife still complains. Maybe I need a new burner coil.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KENNETH from DEEP RUN, NC
- Parts Used:
- 7403P239-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
burned out switch
killed power...removed back of stove...removed switch and replaced it..reinstalled back...powered up
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willis from Anaheim, CA
- Parts Used:
- W10196406RW, WPW10196405, 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Two old Surface Burner Receptacles needed to be replaced.
I followed the instructions given on your great site. Thank you so much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- timothy from south bend, IN
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
surface burner stopped working. Was not heating up.
The repair only took me 10 minutes to do. I purchased the surface replacement kit from partselect.com. The part arrived in two days. The instructions were very simple. I read the instructions on line during my purchase. When I received the new part, I simply did the repair. Including shipping, the cost was less than $20.00. A service call would have been at least 5x the cost. Thank you for being there Partselect. (Tim from south bend indiana)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KAHN T from SAN MARINO, CA
- Parts Used:
- 7403P239-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
I Order 2 Switches For 8" Heating Element
Turn off power 220v, opened cook top, remove old 8" switch and replace with one of the new switch ps2089438. However, I have another cook top, it is a 6" heating element. Can I use the same switch for 8" and use on a 6" heating element? Since I order 2 new ps2089438 switches. Thank you for your anwser. Kahn lee
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Fairmont, WV
- Parts Used:
- 7403P239-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
burner would go to high when turned on
Pulled stove out to unplug. Removed screws holding end covers then remove screws on the underside of cover as you face the stove top.Remove knobs.Pull bottom cover forward and up so you can lift it off to see the insides.Remove wires and attach to the new part one at a time. Unscrew old from the front and attach the new one.Put it back together.Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from San Francisco, CA
- Parts Used:
- 12001676
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Cartridge wire burned out
I was unable to remove the screw which held the electrical element.. so I took the new surface burner receptacle and removed the metal part, and used the old one and put in the new one in the old metal part and rewired, and it is like new.. now I need to do another one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emmett from Rayville, LA
- Parts Used:
- 12001676
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
unable to remove screw with screwdriver
used drill to remove old screw
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elroy from Atwater, MN
- Parts Used:
- 12001676
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
burner not operating or intermittently
Shut off power at breaker box. Removed top burner unit. Removed old receptacle (Mounting screw was rusty so I drilld out the old one.) Cut wires from old unit. Stripped wires back on old unit. Attached old and new wire with ceramic wire nut. Attached new unit. Reinserted top unit. Reconnected power and "voila". Wife was smiling again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vittorio from Wakefield, MA
- Parts Used:
- 12001676
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Electric surface burner would only turn very hot
Well, I had to search a bit deeper in the internet to find out that the problem was not with the surface burner (which did look a bit burned out anyway) but rather with the surface burner switch (Part Number: PS336885) which must have ben damaged by the heat of the closest burner. If this problem would have been better documented (or if I would have searched more carefully) I would have saved over $40 with parts (Surface Burner Receptacle Kit) that I didn't quite need. Repairing the switch was very easy, thanks also to the available video , even though the stove used on this video (front panel) didn't quite match mine (top-back panel).
Was this instruction helpful to you?
Thank you for voting!