KSB5-3 KitchenAid Blender - Instructions

Went to several online blog sites. Repair of the Kitchenaid blender is a hot topic. Could not repair it the way the instructions indicated. One person used a hammer and that did the trick! Who would have thought to use a hammer?!

Last time this happened we simply used a thin wrench to unscrew the damaged coupling. This time it was so tight no wrench could undo it. We had to grind it off using a grinder drill until it was so loose it popped off.

I first tried to do the repair just like the directions ,trying to force off the wheel. Then I tried doing it the way the readers here did with a tthin pliers and was not sucessfull. I then took it to a hardware store and ask about a certain pliers,they did not have it. The older man at the register took two screwdrivers from the jar next to him took my blender and pried on either side and popped off the wheel just like the original directions said. It was then easy to put the new one on.

Following the instructions which was quite clear.

Simply to find the look of dismay in her face. After I violently began shaking and dismantling the compactor in disgust. I decided to unplug it from the wall, I then gathered my senses and began to perform a electrical diagnosis and found that the rotary swich contacts, which activates the compactor, had gone bad. I simply went to the website and selected my part # from the detailed spec sheet. I chose to receive the package on a three day shipment. Here it arrived, installed the part and away the problem went. While on the parts list I included bag brackets that had broke over time and now my compactor is like new.

I used a pair of diagonal cutters to nip away at the drive coupling which had become gummy and soft. This exposed the inner aluminum hub that the drive coupling was molded to. I used several pieces of masking tape to protect the blender finish under the drive coupling. The instruction supplied suggest to pry upward with a screw driver at 1/4 turn intervals until it comes off the motor shaft. I thought this was a rough approach, as I was concerned about damaging the threaded motor shaft. Also note that the motor shaft has left handed threads, you would turn clockwise to loosen the drive coupling. The first approach I tried was to use a small ignition wrench, there are two flats directly below the coupling aluminum hub which measured 9/32" across the flats. The wrench even though small would have to been ground thinner to fit, this may have worked. I decided to use approach two. I used my dremel tool with a 1/32" cut off wheel and cut through each side of the aluminum hub staying away from the center where the motor shaft is threaded. Across the center of the hub I only cut through half the thickness, I then used the diagonal cutters to fold each half agains itself (the hub actually fell off). I installed the new coupling turning it counter clockwise on the motor shaft. I attached the blender jar filled with water with the jar lid on and toggled the blender on and off a few times to further tighten the drive coupling.

used needle nose pliers to hold shaft after prying rubber top off. unscrewed metal tap, counterclock wise. installed new piece

I utilized the "pound the coupling in a clockwise direction" to loosen the coupling. Two good "wackes" and it was loose. Installed new coupling. I found this method in the previous customer installation instructions on the site. Please note that my new part number is ps401661. This part works normally even though my model number did not list a part number, perhaps because my blender is an older model. Without the installation instructions site I would not have known that the thread was a "reverse thread". This site is very helpful. Good luck

I looked on the Web for help in changing this part they suggested prying the part off with a screwdriver. This would work but I figured this approach was a little to brutal.I had a set of distributor wrenches and these had one that fit the shaft under the drive coupling Using the wrench to hold the shaft I used a small set of water pump pliers to remove the coupling.As the directions on the Web states this is a reverse thread.The whole project took all of five minutes to complete

The part comes with instructions on how to replace the coupling. The instruction basically says to pry out the worn coupling. This is exactly what you should do. It might sound strange or brute force but it actually works. The coupling is actually made of some soft metal that comes out easily. The only downside is that you have to clean up the leftover metal bits. You don't need to find a slim wrench for the motor spindle as suggested by other in the thread ..... just follow the instruction pry out the old coupling.

Hammer was used to remove the old one, tapping quickly on old coupling. I did use a thin pliers (wire stripper) to hold shaft when I screwed on new coupling, even though it said one did not need to. Good instruction sheet came with the new coupling.

Took the coupler out with the help of screwdriver and put the new coupler. really easy fix insted of buying a new blender

popped off the old one, popped on the new one. could not have been any easier. :)

Just as the provided instruction says, pry-off old coupling than screw on the new. This repair was too easy! This blender was out of commission a long time, it is good to have it back in use.

Since the coupling is threaded, it can be easily screwed on and off if you immobilize the shaft. If you don't have a tool that can do this (the space between the drive coupling and the body of the blender is only about 1/8"), you can insert a long bladed screwdriver into the vents on the bottom of the blender and into the motor. When you turn the coupling, the motor won't rotate and you can easily screw off the coupling (the threads are reversed, so turn the opposite way). Good luck!
Good