KSB33 KitchenAid Blender - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- jeffrey from Bessemer City, NC
- Parts Used:
- WP9704230
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken base coupling on blender
used thin wire strippers to hold screw shat, than unscrewed one and screwed on the other. done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from Poway, CA
- Parts Used:
- WP9704230
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The rubber coupling that spins the blender dessinagrated
Popped off the old one and popped on the new one. It took no more then 30 seconds and the blender is like new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Glen Ridge, NJ
- Parts Used:
- WP9704230
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The drive coupling wore out
I unscrewed the old coupling and screwed on the new coupling from Partselect.
This was a personal repair job.
However, I am a local Handyman in Northern NJ that does a ton of minor repairs. For all of my appliance part needs I will buy from Partselect.com. They under promised and over delivered! Just incase you dont know what I mean by that statement,,, I ordered the blender part, they told me I would have it in 6-10 days (which was acceptable to me) and I had it in two days... AWESOME job FOLKS!!!!!!!
This was a personal repair job.
However, I am a local Handyman in Northern NJ that does a ton of minor repairs. For all of my appliance part needs I will buy from Partselect.com. They under promised and over delivered! Just incase you dont know what I mean by that statement,,, I ordered the blender part, they told me I would have it in 6-10 days (which was acceptable to me) and I had it in two days... AWESOME job FOLKS!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Phoeniox, AZ
- Parts Used:
- WP9704230
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Teeth on rubber coupling were broken off.
Just like the directions said, I pryed up on the coupling at a few points around it's circumference and it became loose enough to unscrew. I didn't believe it was going to work at first but, amazingly, it did. All that was left to do was screw on the new part. No problem!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from Frenchtown, NJ
- Parts Used:
- WP9704230
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
Coupler broken
It was very easy to unscrew the coupler I used locktight to put on the new part. Thank you sending
the right part the first time
Albert
the right part the first time
Albert
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Athens, GA
- Parts Used:
- WP9704230
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Cup drive on blender was stripped.
Released cup drive with screw driver and un-screwed, screwed on new driver.
That is all, works like a new blender.
That is all, works like a new blender.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PAUL from LAWRENCE, KS
- Parts Used:
- WP9704291
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Blades On Blender Locked Up
Piece of cake. Part was expensive and shipping likewise. Very fast
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from St James City, FL
- Parts Used:
- WP9704230
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
drive coupling broke
Hardest part was taking off the old coupling. I locked the drive with a thin wrench and pryed the coupling off. Took about ten minutes to get off and two minutes to put the new gear on. Remember the thread is counter clockwise. PartSelect was great the part arrived in two days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Raleigh, NC
- Parts Used:
- WP9704230
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rubber on coupling had broken off
using the screw driver I pryed up on the old coupling as out line in the instructions that came with the part. The old part cam off easily and the new one just screwed on. The replacement took only a few minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerome from Salem, MA
- Parts Used:
- WP9704230
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The coupling teeth on the blender broke off when it wasn't seated properly
After reading repair stories on this site, I used wire splicers that just fit between the coupling and housing to hold the shaft while I used pliers to remove the broken coupling. I then hand tightened the new one . It works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from hawthorne, CA
- Parts Used:
- WP9704230
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
coupler wore out
i used the screwdriver method prying up on side to side old one comes off new one goes on pretty cool also it was a nice long flat head with pretty big head
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Polly from Southampton, MA
- Parts Used:
- WP9704230
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Drive coupling wore out
It was harder than the directions said to get the old drive coupling off, but once the old was taken off, it was a piece of cake to put the new one on.
Thanks, great service from this website, received my part the next day after I ordered it!
Thanks, great service from this website, received my part the next day after I ordered it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Naples, FL
- Parts Used:
- WP9704230
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
blender coupler was worn down
Using the precise instructions provided by parts select, I used a big screw driver and pried off the old coupler and cleaned the area and screwed on the new coupler. Fixed!
The part finally arrived 3 weeks later, after being out of stock and back ordered a couple times.
The part finally arrived 3 weeks later, after being out of stock and back ordered a couple times.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Long Beach, CA
- Parts Used:
- WP9704230
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
replace the drive coupling
I couldn't unscrew the old coupling (left hand thread) so I carefully sawed a piece off being careful (the somewhat difficult part of the job) not to damage the threads on the drive motor. Then I used pliers to remove the rest of the drive coupling. Then it's just a matter of screwing on the new coupling. Good as new and I didn't have to buy a new $150 blender.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomasine from WAYNE, NJ
- Parts Used:
- WP9704230
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The original drive coupling disintegrated
I repaired it as per instructions provided by using a flat head screwdriver to pry the original off.
Was this instruction helpful to you?
Thank you for voting!