KSB5MC4 KitchenAid Blender - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Anthony from Conroe, TX
- Parts Used:
- WP9704230
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
i should have read the instructions first,but getting instructions witha purchased part was a total surprise .very simplt with the instructions.i am letting all my friends in on this great company.saved me 100 dallars. tony
Being an aircraft mechanic for years I pride my self on being able to fix anything that my wife buys. So I tried to replace the drive gear for her kitchen aid blender without reading the instructions, much easier to read.
Thanks,
Thanks,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernestine from Madison, ME
- Parts Used:
- WP9704230
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
coupling had broken a couple of pieces off
Intructions were simple. Pried off the old coupling with the screwdriver and applied presser to replace the new one on the spindle.
Comment: KitchenAid appliances are made to last unlike most other small kitchen appliances. They are made of strong materials and repairable where as other similar products get thrown out when they break.
Comment: KitchenAid appliances are made to last unlike most other small kitchen appliances. They are made of strong materials and repairable where as other similar products get thrown out when they break.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mario from Virginia Beach, VA
- Parts Used:
- WP9704230
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
coupling's two extrusions broken
with a flat wrench grab the shaft and unscrew the coupling (note: left handed threads)... then install the replacement part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from Frenchtown, NJ
- Parts Used:
- WP9704230
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
Coupler broken
It was very easy to unscrew the coupler I used locktight to put on the new part. Thank you sending
the right part the first time
Albert
the right part the first time
Albert
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Athens, GA
- Parts Used:
- WP9704230
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Cup drive on blender was stripped.
Released cup drive with screw driver and un-screwed, screwed on new driver.
That is all, works like a new blender.
That is all, works like a new blender.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerome from Salem, MA
- Parts Used:
- WP9704230
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The coupling teeth on the blender broke off when it wasn't seated properly
After reading repair stories on this site, I used wire splicers that just fit between the coupling and housing to hold the shaft while I used pliers to remove the broken coupling. I then hand tightened the new one . It works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from Poway, CA
- Parts Used:
- WP9704230
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The rubber coupling that spins the blender dessinagrated
Popped off the old one and popped on the new one. It took no more then 30 seconds and the blender is like new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- refugio from san francisco, CA
- Parts Used:
- WP9704230
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old coupling got broken
it was too easy, i only used my hand to screw the coupling to the blender.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maryann from Pawtucket, RI
- Parts Used:
- WP9704230
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
So Easy
The coupling split apart on my Kitchenaid Blender. I ordered the coupling part and "Bingo", I was back in business. It took no time at all and one screwdriver. I saved penty of money by not having to buy a new appliance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Long Beach, CA
- Parts Used:
- WP9704230
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
replace the drive coupling
I couldn't unscrew the old coupling (left hand thread) so I carefully sawed a piece off being careful (the somewhat difficult part of the job) not to damage the threads on the drive motor. Then I used pliers to remove the rest of the drive coupling. Then it's just a matter of screwing on the new coupling. Good as new and I didn't have to buy a new $150 blender.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anacleto from West Newton, MA
- Parts Used:
- WP9704230
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
old drive coupling was worn out
I just followed the instructions to remove the old drive coupling and screwed in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from St James City, FL
- Parts Used:
- WP9704230
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
drive coupling broke
Hardest part was taking off the old coupling. I locked the drive with a thin wrench and pryed the coupling off. Took about ten minutes to get off and two minutes to put the new gear on. Remember the thread is counter clockwise. PartSelect was great the part arrived in two days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Raleigh, NC
- Parts Used:
- WP9704230
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rubber on coupling had broken off
using the screw driver I pryed up on the old coupling as out line in the instructions that came with the part. The old part cam off easily and the new one just screwed on. The replacement took only a few minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Suresh from Louisville, KY
- Parts Used:
- WP9704230
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
drive coupling broke
simple clear instructions to follow
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Corona, CA
- Parts Used:
- WP9704230
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rubber drive coupling on blender broke apart
Followed the instructions that came with the replacement drive coupler, first removeing the old part using a screw driver, and then easily screwed on the new part. Removing the old part without the aid of the instructions would have been problematic.
Was this instruction helpful to you?
Thank you for voting!