5KSB52SOB4 KitchenAid Blender - Instructions

I tried turning defective coupler off after inserting a narrow screw driver into the motor fan bladed. That did not work. I then used a wide bladed flat-head screw driver to pry the defective coupler disc off the motor shaft. After prying each side over and over, the old coupler base broke free. I cleaned the remnants of the base from the threaded shaft and then screwed the new coupler on only finger tight. It went on easily. For less than $15.00 (including shipping) we now have a working blender that hopefully will last another 10 years.

As per instructions provided plus other internet advice, we used a large (10 in) flat blade screw driver to pry and remove the existing damaged coupling. There was a small amount of aluminum thread residue left from the old coupling on the motor shaft. We removed this debris, 'lefty tighty'd' the new one and we were blending again! Really simple. We thought about making a 7MM wrench, then we went to our bicycle repair tools, but we the smallest Shimano we had was 10MM. All is well, we have used the blender 3 times with ice and thick stuff with no problems.

This was quite simple and easy to replace.

Just follow directions included with part, very simple and understandable. GOOD BUSINESS, THANK YOU

I was going to throw this expensive blender in the trash but decided to buy the part instead. I'm sure happy that I found this part dealer and was able to fix the blender since it was quite an expensive item. I watched the video on how to replace the coupler and I was able to replace the coupler within minutes and the only tool needed was a screwdriver. I just gently and patiently worked the old one out and basically screwed on the new one. It was very easy and a woman can easily master this repair! I did.

To start with the coupling, I followed the directions by using a flat screwdriver and a thick towel. I placed the towel under the screwdriver to protect the base unit from damage as I pivoted 1/2 of the tip under the coupling, pulling it up as I went around until the coupling popped off. Then I cleaned the remainder of any metal left behind. Then I attempted to screw the coupling on clockwise but the screw opening was slightly to small. So I plugged in the unit and held the coupling with the screwdriver in place and turn the unit on stir and it screwed it on clockwise.
Next, the seal was replaced at the bottom of the jar. And I was finished. Easy as pie.

pry rubber up enough for vice grips, unscrew coupling,left hand threads,screw on new. Came with instructions, in English.

I watched the video on the website and I realized I could repair a $100.00 blender myself, for under $20.00! So, so easy and the part came in two days. Great company, Thanks!

I followed the included instructions.

Removal of the old coupling was easily done by gently prying it up. The threads on ot are much softer that the shaft.

Screwed the new coupling on and done.

I also bought two of these couplings as the rubber on it WILL break off again.

Intructions were simple. Pried off the old coupling with the screwdriver and applied presser to replace the new one on the spindle.

Comment: KitchenAid appliances are made to last unlike most other small kitchen appliances. They are made of strong materials and repairable where as other similar products get thrown out when they break.

i used the screwdriver method prying up on side to side old one comes off new one goes on pretty cool also it was a nice long flat head with pretty big head

Just like the directions said, I pryed up on the coupling at a few points around it's circumference and it became loose enough to unscrew. I didn't believe it was going to work at first but, amazingly, it did. All that was left to do was screw on the new part. No problem!

with a flat wrench grab the shaft and unscrew the coupling (note: left handed threads)... then install the replacement part.

It was very easy to unscrew the coupler I used locktight to put on the new part. Thank you sending
the right part the first time
Albert

Released cup drive with screw driver and un-screwed, screwed on new driver.
That is all, works like a new blender.