KSB5-4 KitchenAid Blender - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ron from Laguna Niguel, CA
- Parts Used:
- WP9704230
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
One of the ears on the gear that drives the blender blade broke off.
Inserted the screwdriver under the original gear and pried it off. After that you just screw the new gear on, it has reverse threads so no tighting is required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CARLOS from MIAMI, FL
- Parts Used:
- WP9704230
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken rotor
I used a screwdriver,pulled out the piece,then change with a new one,that I was ordered before.It was ver easy to assembly.
Was this instruction helpful to you?
Thank you for voting!
coupling and seal wore out
followed instruction, prying off old coupling and screwed new coupling on less than 5 minutes. Parts came in a timely manner. great service, satisfied customer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Tampa, FL
- Parts Used:
- WP9704230
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the couplng "teeth" broke off
popped off the old one, popped on the new one. could not have been any easier. :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Mesa, AZ
- Parts Used:
- WP9704230
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Two teeth broke off the drive coupling
Followed the video you sent removing the old drive coupling. Installed the new part according to instructions. I found I did not need to order the seal. I am a do it yourselfer and have never had such a good experience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sessions from Memphis, TN
- Parts Used:
- WP9704230
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken gear
Very easy. Enclosed instructions were excellent! Part arrived early than anticipated, also.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Virginia from San Diego, CA
- Parts Used:
- WP9704230
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Coupling broke
Just took a screwdriver and pried off the broken coupling as the instruction said with the part. Don't stress it really works and is easy. Ordered the part on Monday and recieved it on Tuesday. Great service from Partselect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Louisville, KY
- Parts Used:
- WP9704230
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Blender coupling cogs were broken
Remove blender jar to get to drive cog. Use a 1/4 to 3/8 flat open-end wrench to hold cog shaft then turn the cog with your hand CLOCKWISE to loosen. Screw new cog gear on COUNTERCLOCKWISE hand tight. Reassemble your blender and you're good to go. It takes a very thin flat wrench but even if you have to buy a set the're not very expensive. Good luck.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Waynesboro, VA
- Parts Used:
- WP9704230
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers
broken rubber coupling on blender base
A very flat wrench or needle nose pliers was needed. I could not get the nut unscrewed with what I had so I had to mail the unit to a service center for repair. They were able to use the part I had purchased but if I had known I wouldn't be able to do it I could have saved a little money in the shipping I had to pay when I ordered the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rodney from long beach, CA
- Parts Used:
- WP9704230
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench set
The old coupling wore off
Thanks to the good advise of those who did this before me ,I know I need a very slender wrench to get between the screwed on base of the coupling and the copy of the base of the blender.
I tried to file one myself, but the metal was too weak. Because i had the size (from what I filed), I measured and knew i needed a 7 MM wrench. I bought one at the parts store and ground it thin enough to slip into the small space and from there it was a five minute job.
I tried to file one myself, but the metal was too weak. Because i had the size (from what I filed), I measured and knew i needed a 7 MM wrench. I bought one at the parts store and ground it thin enough to slip into the small space and from there it was a five minute job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shane from Eglin AFB, FL
- Parts Used:
- WP9704230
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
rubberized coupler broken
Directions included with replacement part were no help...maybe I'm stupid, but prying up on a threaded metal part didn't help unthread it at all.
Vise grips solved the problem. I used vise grips to remove the rubber from the coupler while it was still attached to the blender base, exposing the metal base to the coupler. (yes, I used vise grips to destroy the damaged coupler. after all the hell I went through to try to do it as the directions said, it was very satisfying.)
After removing the rubber, I used the vise grips to bend and distort the metal base until I could get a pair of needle-nose pliers around the drive shaft and hold it still while I unscrewed the now bent-up metal base. Victory!
I thoroughly recommend this method to anyone else, as using vise grips to destroy something is very gratifying.
Vise grips solved the problem. I used vise grips to remove the rubber from the coupler while it was still attached to the blender base, exposing the metal base to the coupler. (yes, I used vise grips to destroy the damaged coupler. after all the hell I went through to try to do it as the directions said, it was very satisfying.)
After removing the rubber, I used the vise grips to bend and distort the metal base until I could get a pair of needle-nose pliers around the drive shaft and hold it still while I unscrewed the now bent-up metal base. Victory!
I thoroughly recommend this method to anyone else, as using vise grips to destroy something is very gratifying.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- don from laguna woods, CA
- Parts Used:
- WP9704230
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
blender coupler had disintegrated
Read provided instructions but unfortunately looked at part and re-interpeted the instructions....Should have just followed instructions as printed. I tried to pry up and unscrew instead f just prying off...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Townsend, DE
- Parts Used:
- WP9704230
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Wrench set
Coupler teeth missing
Followed instruction sheet, but as it stated just remove by hand, not so, had to grind open end wrench to fit between coupler and base to fit flat sides of shaft, then use channel locks to break lose and to unscrew most of the way off.
But in the end the part worked just fine.
But in the end the part worked just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alexander from West Bend, WI
- Parts Used:
- WP9704230
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Rubber drive coupling disintegrated
Tried to follow the included instructions - no way that just prying the coupler off would work without bending the shaft and wrecking the threads! Then used a flat, open-ended 7mm wrench to hold the shaft and pliers to remove the coupling. The coupler was so tight that I could not unscrew it without the wrench slipping. Ended up shoving a screwdriver through the fanblade from the bottom (unplug it first!) and use the pliers to unscrew the coupler (remember, it's a left handed thread!)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- linda from whitman, MA
- Parts Used:
- WP9704230
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
could not remove the broken coupling, on the blender with tools we had at home
it need a special tool...to remove the broken coupleing..had to have my brother-in-law who fixes industrial equipment, remove it with a special tool, that a home owner would not have
Was this instruction helpful to you?
Thank you for voting!