4KSB5 KitchenAid Blender - Instructions

Because the old coupling was so tightly screwed onto the shaft it was necessary to use very flat wire crimpers to slide between the old coupling and the blender housing to grip the shaft and immobilize it while pliers were used to grasp the old coupling and loosen it---rotate clockwise.

I followed the instructions on the sheet that came with the replacement part. The instructions are accurate, however, the working is misleading. I think additional information is needed to make the install easier. First, a flat head screwdriver works best. Also, all the rubber that is on the broken coupling needs to be removed before trying to get the coupling off. Once all the rubber has been removed then it becomes easier to see the metal rod that holds the coupling and distance between the coupling and the base of the blender, take the screwdriver and gently pry the coupling off in an upward movement while going around in a circular manner. Then you can see the coupling rising up from the rod. Then take a hold of the broken coupling and pull it off. Then attach the new coupling, screwing it on counterclockwise. Once you realize what is going on, it's actually quite easy.

Went to several online blog sites. Repair of the Kitchenaid blender is a hot topic. Could not repair it the way the instructions indicated. One person used a hammer and that did the trick! Who would have thought to use a hammer?!

used needle nose pliers to hold shaft after prying rubber top off. unscrewed metal tap, counterclock wise. installed new piece

I used a pair of diagonal cutters to nip away at the drive coupling which had become gummy and soft. This exposed the inner aluminum hub that the drive coupling was molded to. I used several pieces of masking tape to protect the blender finish under the drive coupling. The instruction supplied suggest to pry upward with a screw driver at 1/4 turn intervals until it comes off the motor shaft. I thought this was a rough approach, as I was concerned about damaging the threaded motor shaft. Also note that the motor shaft has left handed threads, you would turn clockwise to loosen the drive coupling. The first approach I tried was to use a small ignition wrench, there are two flats directly below the coupling aluminum hub which measured 9/32" across the flats. The wrench even though small would have to been ground thinner to fit, this may have worked. I decided to use approach two. I used my dremel tool with a 1/32" cut off wheel and cut through each side of the aluminum hub staying away from the center where the motor shaft is threaded. Across the center of the hub I only cut through half the thickness, I then used the diagonal cutters to fold each half agains itself (the hub actually fell off). I installed the new coupling turning it counter clockwise on the motor shaft. I attached the blender jar filled with water with the jar lid on and toggled the blender on and off a few times to further tighten the drive coupling.

I looked on the Web for help in changing this part they suggested prying the part off with a screwdriver. This would work but I figured this approach was a little to brutal.I had a set of distributor wrenches and these had one that fit the shaft under the drive coupling Using the wrench to hold the shaft I used a small set of water pump pliers to remove the coupling.As the directions on the Web states this is a reverse thread.The whole project took all of five minutes to complete

Hammer was used to remove the old one, tapping quickly on old coupling. I did use a thin pliers (wire stripper) to hold shaft when I screwed on new coupling, even though it said one did not need to. Good instruction sheet came with the new coupling.

Removed reverse thread coupler, jammed screw driver into fan blade at bottom of mixer, installed new coupler. REMEMBER, REVERSE THREAD!

Just as the provided instruction says, pry-off old coupling than screw on the new. This repair was too easy! This blender was out of commission a long time, it is good to have it back in use.

The part comes with instructions on how to replace the coupling. The instruction basically says to pry out the worn coupling. This is exactly what you should do. It might sound strange or brute force but it actually works. The coupling is actually made of some soft metal that comes out easily. The only downside is that you have to clean up the leftover metal bits. You don't need to find a slim wrench for the motor spindle as suggested by other in the thread ..... just follow the instruction pry out the old coupling.

Inserted the screwdriver under the original gear and pried it off. After that you just screw the new gear on, it has reverse threads so no tighting is required.

Took the coupler out with the help of screwdriver and put the new coupler. really easy fix insted of buying a new blender

Since the coupling is threaded, it can be easily screwed on and off if you immobilize the shaft. If you don't have a tool that can do this (the space between the drive coupling and the body of the blender is only about 1/8"), you can insert a long bladed screwdriver into the vents on the bottom of the blender and into the motor. When you turn the coupling, the motor won't rotate and you can easily screw off the coupling (the threads are reversed, so turn the opposite way). Good luck!
Good

followed instruction, prying off old coupling and screwed new coupling on less than 5 minutes. Parts came in a timely manner. great service, satisfied customer

I used a screwdriver,pulled out the piece,then change with a new one,that I was ordered before.It was ver easy to assembly.