CA14WC00 Whirlpool Air Conditioner - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- SHIRLEY G. from Mabank, TX
- Parts Used:
- WP1182336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter was filthy, no telling how long it had been since changed
Took out old filter and replaced it with the new filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Chesapeake, VA
- Parts Used:
- 1183372
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
window ac thermostat stuck in on position
Part came quickly, was the right part and went in quickly. Only had to drill out 3 rivets anre reasemble with sheet metal screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from Northfield, OH
- Parts Used:
- 1183372
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Air conditioner kept "hard starting" - Not kicking the compressor readily
Well - first I thought the problem was the capacitor, as that will cause hard starts, especially on an air conditioner (I am no HVAC man, but researched this to find out). Pulled the capcitor (BE CAREFUL - discharge first - It CAN kill you if you don't!). Tested it and found it fine (again - to test - research on the net - VERY easy w/ a standard Ohm meter).
So - after investigating a few other possibilities, I sat and listened to the thing run and realized it was cycling too fast (trying to kick the compressor on too close to shutting it off, hence the built up pressure was still too high to kick the compressor on easily. Figured maybe the thermostat was causing this (kicking the compressor on before it was "rested").
I was correct. It solved the problem.
To change the thermostat took like 5 minutes.
BTW - CLEAN YOUR COILS - I'M SURPRISED MY WAS EVEN RUNNING! THE COILS WERE FULL OF JUNK. If your coils are dirty the thing is will not run well and will cost you a lot of money to make your room / house cool!
Hope this helps somebody!
So - after investigating a few other possibilities, I sat and listened to the thing run and realized it was cycling too fast (trying to kick the compressor on too close to shutting it off, hence the built up pressure was still too high to kick the compressor on easily. Figured maybe the thermostat was causing this (kicking the compressor on before it was "rested").
I was correct. It solved the problem.
To change the thermostat took like 5 minutes.
BTW - CLEAN YOUR COILS - I'M SURPRISED MY WAS EVEN RUNNING! THE COILS WERE FULL OF JUNK. If your coils are dirty the thing is will not run well and will cost you a lot of money to make your room / house cool!
Hope this helps somebody!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Liberty, MS
- Parts Used:
- WP1182336
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Needed new Ice Maker
Removed back cover, and installed the water valve. Removed the water supply tube cover and installed the supply tube. Opened freezer and removed the electrical cover, removed the knockouts and pulled line out. Hooked up ice maker and installed it to wall. Turned water on and waited a couple hours, it is making ice. Installing the ice maker was easy. Running water line to it........well that is another story. LOL.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rhea from Plainview, TX
- Parts Used:
- WP1182336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old filter had become brittle & needed replacing
Just removed the old filter and replaced. Slid right in, no tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- susan from Socorro, NM
- Parts Used:
- WPY015825
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Both motor clips broken - >40 year old dryer!!
Removed the back - Saw the broken clips on the base of the dryer (the wires to the motor were pulling out because the motor was slipping).
Guessed that the parts were motor clips (no pix in the web site!)
Got the parts in post - they were identical except needed some rubber grips inside to hold tight (Used pieces of bike tire inner tube cut to fit for this.) Attached clips. Works fine!!
(Son is an engineer - he found the problem. Husband is a retired doctor - he couldn't!! but together they
supplied the muscle)
Sue (67 years old)
Guessed that the parts were motor clips (no pix in the web site!)
Got the parts in post - they were identical except needed some rubber grips inside to hold tight (Used pieces of bike tire inner tube cut to fit for this.) Attached clips. Works fine!!
(Son is an engineer - he found the problem. Husband is a retired doctor - he couldn't!! but together they
supplied the muscle)
Sue (67 years old)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan J from Oneonta, NY
- Parts Used:
- WP8031121
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no on/off knob
even I can replace a control knob....
Was this instruction helpful to you?
Thank you for voting!