Whirlpool Washer Suspension Spring WP63907 | Fix.com

Suspension Spring

&SeePartX&
11743345-1-S-Whirlpool-WP63907-Suspension Spring
https://www.fix.com/Schematics/Maytag/OGHXSQCE.gif
Click for the BBB Business Review of this Appliances - Small - Supplies & Parts in Dartmouth NS
Part Description:
Sold Individually.
This part fixes the following symptoms: Shakes and moves, Noisy, Leaking.
This part works with the following brands:
Part number cross reference:
This part works with the following products:
Washer, Washer Dryer Combo.

Installation Videos

Replacing your Whirlpool Washer Suspension Spring
Watch this how to video with simple, step-by-step instructions for a successful DIY repair.
Fixes the following symptoms:
  • Washer tub is off balance/off centre and noisy
  • Washer tub is slamming into washer body during spin cycle
Tools used for this repair:
  • 1/4" Nut Driver
  • Flat blade screw driver
  • Needle Nose Pliers
  • Putty Knife

Installation Instructions

Showing 1-10 of 11 Instructions
>
page 1 of 2
<

Very easy

Took of the housing to the washer and replaced the springs Thanks for your help

Were these instructions helpful?

1 of 2 people found these instructions helpful
Parts Used: Tub Spring , Suspension Spring
Difficulty Level: Very Easy
Total Repair Time: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: Cesar from Kissimmee, FL

Just to understand the type and different model videos

exactly as the video mentioned, just need to explain if some models are alike or different using the same part numbers will be awesome.in my case my washer had the screws in different areas to disassemble and Assembly the spare parts, other than that beautiful idea in sending the link video with the email confirmation let me tell you first class and top of the line customer service rated 5 Stars

Were these instructions helpful?

1 of 2 people found these instructions helpful
Parts Used: Tub Spring , Leveling Spring , Suspension Spring
Difficulty Level: Really Easy
Total Repair Time: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: CARLOS from EL PASO, TX

Unbalanced spinning

My washer is operational now. Thanks

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Suspension Spring , Agitator Directional Cogs
Difficulty Level: Really Easy
Total Repair Time: 30 - 60 mins
Tools: Pliers, Screw drivers, Socket set
Customer: Timothy from San Antonio, TX

Unbalanced spinning

My washing machine is operational. Thanks

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Suspension Spring
Difficulty Level: Really Easy
Total Repair Time: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: Timothy from San Antonio, TX

Washer would walk and violently shake on spin cycle

On the bottom of the control panel there are two Phillips head screws you have to take out. Flip up the control panel and it will rest on its own hardware. Next pop off both golden locking tabs that are now exposed from underneath the control panel. Now the whole porcelain body will slide off forward. Use pliers to take off and replace the 4 Springs. Assembly is the reverse.

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Tub Spring , Suspension Spring
Difficulty Level: Easy
Total Repair Time: Less than 15 mins
Tools: Pliers, Screw drivers
Customer: Jd from Cedar Springs, MI

Machine vibrates excessively when in spin cycle either with or without clothes in washer.

I watched the video tip on this site and then preformed my repair. This was a very easy repair and my washing machine no longer vibrates excessively in the spin cycle. I used a 5/16 nut driver to unscrew the fasteners and held the bracket with my hand to ease the tension. Make sure to put the spring on the same way it came off the bracket. Put some grease on the spring tips for lubrication. I had a slight challenge getting the enclosure reinstalled on my machine that took most of the repair time. Thanks for the fast shipping and helpful video on your website. I appreciate saving money and time.

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Tub Spring , Suspension Spring
Difficulty Level: Easy
Total Repair Time: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers, Socket set
Customer: Karl from Minneapolis, MN

Tub bangs against frame or enclosure

1. remove two screws holding control panel, then swing up. 2.remove two flat spring keepers on case top, disconnect the door switch connector at back or top case. 2 tilt entire case foreward and remove. replace the three springs and clips at bottom of tub. I had to bend the clips a bit more with a hammer and vise to make them more hook shape where they fit into the frame. 4. reassemble everything in the reverse order. I unplugged the washer but left the water and drain connected.

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Retainer, Suspension Spring , Suspension Spring
Difficulty Level: Easy
Total Repair Time: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: jerry from loveland, CO

Washer would shake and dance all over the floor during spin cycle even if load was balanced out.

To make a long story short, I watched the video on this parts website and followed their instructions. Worked perfectly. It came apart, parts replaced and assembled just as video stated. Simple repair. Thanks so much for the video help and will always come to this site for help and parts. Can't beat the delivery time also, ordered on sunday and parts were here on tuesday.

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Tub Spring , Suspension Spring
Difficulty Level: Really Easy
Total Repair Time: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: James from MCEWEN, TN

Washer would vibrate bad during spin cycle

Took outer cover off & replaced suspension springs

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Tub Spring , Suspension Spring
Difficulty Level: Really Easy
Total Repair Time: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: Ryan from sherrard, IL

Washer severely out of balance and walking around on spin cycle

Video shows taking the control panel and case apart. Not needed in my case. Laid the washer on its back without taking any of the above apart. Made fixes just from the open bottom which had two of the springs with relaxed tension. 1/4" socket to remove the spring brackets, changed springs, reassembled. To get to the 3rd spring, laid the unit on its front causing that one to relax. Very easy. Now we have a washer which is quiet and staying in one place working like new ! Fantastic service and very fast delivery from this site !

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Suspension Spring
Difficulty Level: Really Easy
Total Repair Time: 30 - 60 mins
Tools: Socket set
Customer: Brian from Lawrenceville, GA
Showing 1-10 of 11 Instructions
>
page 1 of 2
<

Model Cross Reference List

This part works with the following models:

Fix Number: FIX11743345
Manufacturer Part Number: WP63907


Brand Model Number Description
Kenmore11010202000Washer
Kenmore11010202001Washer
Kenmore11010502990Washer
Kenmore11010502991Washer
Kenmore11010852990Washer
Kenmore11010852991Washer
Kenmore11012202100Washer
Kenmore11012502100Washer
Kenmore11012852100Washer
Kenmore11013202200Washer
Kenmore11013212200Washer
Kenmore11014102300Washer
Kenmore11014112300Washer
Kenmore11014202300Washer
Kenmore11014212200Washer
Kenmore11014222300Washer
Kenmore11014502300Washer
Kenmore11014852300Washer
Kenmore11015732400Washer
Kenmore11015842400Washer - Kenmore Washing Machine
Kenmore11015852400Washer
Kenmore11015862400Washer
Kenmore11015864400Washer
Kenmore11015942400Washer
Kenmore11015942401Washer
Kenmore11015944400Washer
Kenmore11015944401Washer
Kenmore11015952400Washer
Kenmore11015952401Washer
Kenmore11015954400Washer